GP U-Can-Do-3D Review
by Meyrick Camilosa

Model Name:  Great Planes U-Can-Do-3D

Scale:  N/A

Wingspan:  65"

Length:  68"

Weight:  7.6 lbs.

Wing Area:  1024 sq in.

Wing Loading:  17.10 oz/sq ft.

Engine Used:  Saito 100

Prop Used:  APC 16x4W

Fuel Used:  Powermaster 20/20

Radio Used:  Futaba 9ZWCII

Servos Used:  (2) Futaba 9303 on Ailerons, (2) Futaba 9402 on each elevator halves, (1) Futaba 9402 on rudder, (1) Futaba 9001 on throttle


Included with Kit

  • Built-up and covered fuselage and 1 piece wing
  • Fiberglass painted cowl and wheel pants
  • Clear canopy
  • 2-56 hardware
  • Slim Fuel Tank
  • CA hinges
  • Wheels
  • Alluminum landing gear
  • Other necessary hardware

Added Modifications

  • Sulivan 4-40 rods
  • Klett Hinges

Random Pictures

Power is a Saito .91 swinging an APC 16x4W propeller at 8600 RPMs.
(Upgraded to a Saito 100)
Added 3 washers on the left side of the engine mount to get 3 degrees of right thrust for perfect straight up lines.

Changed the rudder's 2-56 rod to 4-40 because it kept bending.  Left the 2-56 rod on the elevators and have had no problems.
Changed the aileron's 2-56 rod to 4-40.

45 degree throws on the tail group.

Assembly

Assembling the kit was very easy.  This is the fastest ARF I have ever built (6-1/2 hours).

Wings:  The wing was 1 piece out of the box.  The only thing I had to do was hinge the ailerons and that didn't take too long as I used Klett hinges.

Fuselage:  The fuse is long and had plenty of room in the radio compartment.  The horizontal stab required only two screws, that was already supplied, to be mounted.  The vertical fin required to be glued to the fuselage.  I also used Klett hinges on the tail group.

Other Things:  Cowl had plenty of room for my Saito and is a perfect fit.  Wheel pants required gluing of the screw block.  Landing gear required drilling of two holes per side for the wheel pants screws.  I had to buy hardened drill bits to drill the hard landing gear.  Cockpit required cutting out the shape and I just taped it to the fuselage with packing tape.


3D Flight Performance Rating

(1 = worst / 10 = best)

Hovering:  (9)   Very easy, even on windy conditions.

Torque Roll:  (6)  Required some aileron inputs on some occasions.

Knife Edge:  (10)  Very powerful rudder, only plane I know that can execute a Knife Edge Wall.

Wall:  (9)  Very fast and stops on a dime.

Parachute:  (9)  Very fast just like the wall.

Elevator:  (9)  Very steady with 45 degree spoileron mixes.

Blender:  (8)  It does the Blender but not as extreme as scale models.

Harriers:  (3)  Rocks the wing like crazy even with spoilerons.

Inverted Harriers:  (6)  More stable than upright Harriers.

Snap Roll:  (4)  It looks more like a lazy Barrel Roll.

Knife Edge Spin:  (7)  Very slow and looks neat with added flap mixes.

Flat Spins:  (6)  Not as flat.

Inverted Flat Spins:  (8)  Better than upright Flat Spins.


 

Restored from the Internet Archive, 2026 · about this archive