ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

another update on my progress:funtana 90
8 posts
 
   3DBatix Forum Index -> 3D Talk
 
Author Message
Rcflyer



Joined: 01 Jul 2004
Posts: 62

PostPosted: Wed Aug 18, 2004 10:38 pm    Post subject: another update on my progress:funtana 90  

I have got the tail section done,main gear,wheels, and wheel paints on. When i opened the canopy up i accidently in the proccess cracked the canopy down the middle the canopy is really thin and franigly i noticed and oviousely found out but called horizane up and paid for 2 day shippping my mistake costed me about $21 bucks but oh well next one ill use scicssors and not try to ripe it apart again lol but anyways thats it for now got to go see you all later.
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 668
Location: Fremont, CA

PostPosted: Thu Aug 19, 2004 9:43 am    Post subject:  

Cool, mine is still in the box. Very Happy
_________________
--Meyrick--
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 124
Location: Jackson, MS

PostPosted: Thu Aug 19, 2004 12:22 pm    Post subject:  

Great job!! Laughing

Be sure to check the ribs for breaks, cracks, missing balsa pieces in the ribs. I thin CA'd all my ribs and use small nylon pieces to reinforce the servo tray ribs. This didn't add much weight at all, but it should have stiffened up the ribs increditably. Be sure that the servo tray in the wing is well attached and that particular rib is not broken or even cracked. To be safe, put some thin CA on it just to be safe. I believe this is why some Funtana's are going in.

I haven't flown mine yet, but I have flown a buddy's several times and literally have a blast each time. My YS 1.10FZ came in on Monday after waiting a month while it was on back or. Now I have to each popcorn and pistachios for dinner for a while while my account heals. Wink

BE SURE, BE SURE, BE SURE that you have mechanical advantage at the servo and not the control horn. What servos are you using? If you are using the minimum torque (50oz) servo, this will work as long as you have mechanical advantage. If you have mechanical disadvantage, the torque used by the 50oz servo may actually be 25oz, 30oz, 35oz, etc...

I have HS-5645MG digital servos for mine. They produce 168oz torque. With this aileron being 5.5" wide (root), 3.5" (tip) and 28.5" long, this plane really needs more than a 50oz servo as the min. I think a 80 would be a better minimum. Fly the plane slow and you should be ok.

Also, I would change the tailwheel also. I really hate the tailwheel that comes with the kit. Get a Sullivan 5-12 lbs tail wheel, it is much better (spring action). Peel back the fuse covering and use blind nuts to attach it to the fuse. I have a wire tail brace that I am going to install also. I pinned my firewall also since I am going to use a YS 1.10. No one has mentioned any problems, but this is just a little insurrance for my mind. Some are cotter clipping their wing tube also. Fiberlite has a lighter landing gear that is taller also if you are into that. The changes ans additions I did should add too much weight, but should make the plane more stout. There are other small changes and additions that can be done, but you should be set once you get your plane setup.

DTB

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
Rcflyer



Joined: 01 Jul 2004
Posts: 62

PostPosted: Thu Aug 19, 2004 7:03 pm    Post subject:  

i am using 70 oz torge on everything exectp the rudder, using a digital servo (100 oz torqe) for the rudder and I changed the tail wheeel out to and put a suilven on it and I do not have any cracks on anything exepct wrenckles

hey meyrick got anything on the bench? a pearon always needs something to build, the funtana come together nicely


thanks for your repaly everyone
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 668
Location: Fremont, CA

PostPosted: Thu Aug 19, 2004 8:30 pm    Post subject:  

Rcflyer wrote:

hey meyrick got anything on the bench? a pearon always needs something to build, the funtana come together nicely


Just a couple foamies I'm finishing up. I should be starting on the Funtana in a week or two. I will have a Saito 120 with an APC 17x4W prop on it. I haven't decided on the servos. Maybe Fut S9402 since I already have a couple spares. This plane looks really nice, even in the box. Mr. Green

_________________
--Meyrick--
Back to top  
Rcflyer



Joined: 01 Jul 2004
Posts: 62

PostPosted: Fri Aug 20, 2004 8:57 am    Post subject:  

yeah it is a nice plane waht happen to the 100? decide to still keep it on the ucando3d?
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 668
Location: Fremont, CA

PostPosted: Fri Aug 20, 2004 9:07 am    Post subject:  

Rcflyer wrote:
yeah it is a nice plane waht happen to the 100? decide to still keep it on the ucando3d?


Yeah, I'm discovering more tricks on the U-Can-Do and actually having so much fun with it right now and I couldn't just retire it. I'm shooting for at least 500 flights before she gets decommissioned. She's got about 350+ now.

_________________
--Meyrick--
Back to top  
Rcflyer



Joined: 01 Jul 2004
Posts: 62

PostPosted: Fri Aug 20, 2004 7:25 pm    Post subject:  

thats cool ill just give you review on how it flies with a 100 in it
Back to top  
 
   3DBatix Forum Index -> 3D Talk All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive