ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Foam-e 3D Flutter
7 posts
 
   3DBatix Forum Index -> Foamies
 
Author Message
erogala



Joined: 17 Aug 2007
Posts: 4

PostPosted: Fri Aug 17, 2007 3:30 am    Post subject: Foam-e 3D Flutter  

Just completed the Foam-e 3D design. Built per plans but used 3mm material for Horizontal Stab and Wing. Experiencing flutter on the Ailerons and Elevator.

Anyone have any experience with using 3mm material on these surfaces and how/what did you do to eliminate flutter?

Motor is a Himaxx HC2812-0850 running 3 cells and an APC 10 x 4.7 SLo-Fly prop. This flutter is occuring at approximately 1/3 to 1/2 throttle. I understand throttle management, so this is not just a speed issue.

Looking for solutions!
Back to top  
3dbatixkid
Site Admin


Joined: 15 Apr 2004
Posts: 1545
Location: Sunnyvale, CA

PostPosted: Fri Aug 17, 2007 9:02 pm    Post subject:  

You can try putting flat carbon on the TE of the surfaces, or slotting the center of the surface and drop in a flat piece of carbon.
_________________
Zak West :smt029

http://www.DesertAircraft.com

http://www.Smart-Fly.com

http://www.LeeUlingerModels.com

http://www.CoolRunningUSA.com

Fromeco Scale Avionics

Sala Series DA Mods
Back to top  
erogala



Joined: 17 Aug 2007
Posts: 4

PostPosted: Sat Aug 18, 2007 2:56 am    Post subject: Foam-E 3D Flutter  

Thanks Zak,
Ive tried two things to minimize the flutter:
1- Reduced the chord of the ailerons by 1"
2- Added carbon-fiber strips (.019 x .118) to the TE of the ailerons

Both have seemed to help but, the flutter is still there.

My conclusion, build a new airframe and make it all out of 5mm material.

BTW- I build all of my foamies from Cellfoam

Comments?

The "Hobby Guy"
Back to top  
3dbatixkid
Site Admin


Joined: 15 Apr 2004
Posts: 1545
Location: Sunnyvale, CA

PostPosted: Mon Aug 20, 2007 12:36 pm    Post subject:  

Ive never used the cellfoam, only depron. Building the plane out of all 5 or 6mm foam is the way to go.
_________________
Zak West :smt029

http://www.DesertAircraft.com

http://www.Smart-Fly.com

http://www.LeeUlingerModels.com

http://www.CoolRunningUSA.com

Fromeco Scale Avionics

Sala Series DA Mods
Back to top  
erogala



Joined: 17 Aug 2007
Posts: 4

PostPosted: Wed Sep 12, 2007 2:09 am    Post subject:  

Have been flying a new version of this design with 5mm Cellfoam and all is well! Thanks for the advice/suggestions
given to me several weeks ago.

Anyone else building their foamies with Cellfoam?

Thanks again!

The "Hobby Guy"
Back to top  
erogala



Joined: 17 Aug 2007
Posts: 4

PostPosted: Wed Sep 12, 2007 2:09 am    Post subject:  

Have been flying a new version of this design with 5mm Cellfoam and all is well! Thanks for the advice/suggestions
given to me several weeks ago.

Anyone else building their foamies with Cellfoam?

Thanks again!

The "Hobby Guy"
Back to top  
stillhalfnewb



Joined: 20 Apr 2008
Posts: 7

PostPosted: Thu Apr 24, 2008 2:56 pm    Post subject: Re: Foam-e 3D Flutter  

i also build with cell foam because thats all i have around here. i guess thats what you get for living in idaho.
Back to top  
 
   3DBatix Forum Index -> Foamies All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive