ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

FUNtana
4 posts
 
   3DBatix Forum Index -> 3D Talk
 
Author Message
Radioflyer



Joined: 14 Sep 2004
Posts: 105
Location: Kalamazoo, MI

PostPosted: Tue Sep 14, 2004 1:48 pm    Post subject: FUNtana  

I'm new at this so please be nice. I purchased a Funtana this summer and have only 8 flights on it. After the first 2 flights I noticed both wing dowels were loose and had been scored all the way around. that was doing no 3D,just regular Rolling Eyes flying. I fixed that and moved the balance point back. (ruffly5.5 inches back) More flying was done . I am totally pleased with the quality of stability of flying, but with the CG so far forward hovering was though to say the least. I moved the CG back to 6.25 inches and my funtana became quite unstable when i pulled the stick back, It would fall out.I can't say if it was the same side every time or not. I even switched the spoilerons to flapperons and this didn't solve the problem. It did prolong it alittle. I've watched the videos of Zack flying his funtana and his seems to fly much more stable. Is it me or the plane? I also noticed more scoring on one of the wing dowels. What can I do about that? One more, I put a Saito 82a in it and have 15x4 wide blade APC , is this a good combination for 3D flying? I can't beleive I'm have this much trouble with a Funtana when I can do tailtouches with a modified Tower Uproar w/ a JRmax 4 fm. thanx for replies and keep the dirt off the prop.
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 615
Location: Sunnyvale, CA

PostPosted: Tue Sep 14, 2004 8:52 pm    Post subject:  

I had the same problem with the dowls in my funtana. Mine were so bad, that it actually broke one of them in the air. I sovled the problem by putting carbon tube around the dowl, and putting a brass tube in the fuse where the dowl plugs in. I also found that the holes were up too high in the fuse, so the holes needed to be opened a bit. As for the unstable flying, i dont know what to say. I have had a lot of people ask me about this. Try moving the cg forward about a half inch. I know mine wasnt too tailheavy, since inverted flight it dropped just a tiny bit with hands off. The saito 82 should power it fine, and i think you have the right prop for your combo.
_________________
Zak West
Team DA

Desert Aircraft

Smart Fly

Fromeco Avionics

Stick and Rudder Photos
Back to top  
Radioflyer



Joined: 14 Sep 2004
Posts: 105
Location: Kalamazoo, MI

PostPosted: Wed Sep 15, 2004 12:32 pm    Post subject:  

Thanx for the advise. I'll get those dowels fixed and adjust the CG before

the next flight. I'm also doing alot of reworking of the guts of my plane. I'm

relocating the throttle servo and going to a mini, and forgot about the weight

I put in the nose. Thats gonna get remove and battery relocated. I also

noticed my ailerons off by about an eighth of an inch to the left to fly level

so I heated both wing panels and twisted them. Hopefullly all this will cure

the bugs. You have a great sight and in the last few days I have learned

more than I have in a year. Very Happy
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 615
Location: Sunnyvale, CA

PostPosted: Wed Sep 15, 2004 8:52 pm    Post subject:  

Glad to help Cool
_________________
Zak West
Team DA

Desert Aircraft

Smart Fly

Fromeco Avionics

Stick and Rudder Photos
Back to top  
 
   3DBatix Forum Index -> 3D Talk All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive