ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Chief Aircraft 72" Katana For Sale
21 posts
 
   3DBatix Forum Index -> Buy & Sell
 
Author Message
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Sat Sep 18, 2004 10:04 am    Post subject: Chief Aircraft 72" Katana For Sale  

I have a Chief 72" Katana (newer wing design) for sale. Selling to finance my next project. Here is the list of the whole sha-bang:

-OS 160 fx (runs great)
-Bisson Pitts Mufffler
-Zinger Pro 18x8 Prop
-Polished True Turn 3" Spinner
-5 Hitec digital HS5625MG-J Servos (futaba connectors) all surfaces
-1 Futaba S3001 for throttle.
-Hd JR switch with dsc/chg jack
-Futaba 6v 5 cell nicad 1000 mAh
-SWB aluminum servo arms on all control surfaces except rudder

MODS
-Added Top hatch
-Wing retention uses wing nuts inside fuse instead of springs(2 pc wing)
-All hardware replaced:
Dubro ball links/ 4-40 rods all surfaces
Sullivan steel horns all surfaces
Dubro 5/32 steel wheel axles
H9 aluminum engine mount
20oz tank with sullivan Al cap, PSP Al fuel dot
-Rudder servo moved fwd w/ cable pull-pull (uses kit incl. Al servo arm)
-Dubro Hd cotter pin hinges on all surfaces
-GraphTech carbon fiber gear
-Rc Blimp Productions tail wheel
-Sullivan 3'' Skylite wheels




It is built as light as possible, the dry weight is 12.8 Ibs. The build quallity is very nice. It flys great and has 55 degrees of throw on all the control serfaces. It does all the 3d maneuvers you can throw at it.

Asking $650 (Build cost was greater than $1000)

Shipping paid by buyer or can be picked up (San Jose, CA area)

I will see if I can get some pics up.
Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Sun Sep 19, 2004 12:18 pm    Post subject:  

Here is a pic of the above.


TomsKatana01.jpg
 Description:
 Filesize:  70.23 KB
 Viewed:  666 Time(s)

TomsKatana01.jpg


Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Sun Sep 19, 2004 7:37 pm    Post subject:  

...


TomKatana1.jpg
 Description:
 Filesize:  64.83 KB
 Viewed:  640 Time(s)

TomKatana1.jpg


Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Sun Sep 19, 2004 7:39 pm    Post subject:  

...


TomKatana2.jpg
 Description:
 Filesize:  55.65 KB
 Viewed:  639 Time(s)

TomKatana2.jpg


Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Sun Sep 19, 2004 7:41 pm    Post subject:  

...


TomKatana3.jpg
 Description:
 Filesize:  46.15 KB
 Viewed:  638 Time(s)

TomKatana3.jpg


Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Sun Sep 19, 2004 7:44 pm    Post subject:  

...


TomKatana4.jpg
 Description:
 Filesize:  39.76 KB
 Viewed:  637 Time(s)

TomKatana4.jpg


Back to top  
3Dfanatic



Joined: 15 Apr 2004
Posts: 300
Location: Tacoma(area), WA

PostPosted: Sun Sep 19, 2004 9:55 pm    Post subject:  

Would you sell it airframe only?
_________________
-Aaron

cutimages.com
offthewallrc.com
Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Mon Sep 20, 2004 5:28 pm    Post subject:  

I don't really want to do that. I am only 13 and I am dirt cheap Crying or Very sad . I want the money to help me buy the 81'' Velox from Aerotech, that is $400. Why do you want the airframe? Maybe I can sell it w/o the engine for $475 or w/o the the bat. and servos for the same.
Back to top  
john wondra



Joined: 05 May 2004
Posts: 360
Location: auburn, wa

PostPosted: Mon Sep 20, 2004 9:11 pm    Post subject:  

hey aaron and i want the katana airframe only because i have a bme 44 laying around in a plane with servoes and everything redy to fly. we just want somthing to dump it all into and that bme 44 would be a screemer on that katana let me know. john
_________________
John Wondra RAMS VP
Team 3D Foamy/3D Foamy Suport
__________________________
www.3dfoamy.com
www.northwest3d.com
www.e-flightline.com
www.Falconbatteries.com
www.cutimages.com <all your custom vinyl needs>
Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Tue Sep 21, 2004 7:06 am    Post subject:  

I can't sell the airframe for anything near $400 Mad . So I would like not to. Sorry.
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 367
Location: Canada

PostPosted: Tue Sep 21, 2004 12:19 pm    Post subject:  

you would have better chance at selling if you split up IMHO
_________________
-Chris-
3D Foamy
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1312
Location: Fremont, CA

PostPosted: Tue Sep 21, 2004 12:37 pm    Post subject:  

I've seen this plane fly, it does awesome 3D with Tom behind the sticks.

Hey Tom, are you planning on stepping up to bigger planes for IMAC?

_________________
--Meyrick--
Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Tue Sep 21, 2004 3:59 pm    Post subject:  

Yes I am getting the 81'' Velox from AeroTech with a da 50 for IMAC and for a more rock solid 3d flyer. Also I could put a smoke system on it laughing. It is just a bigger heavier plane and I think that it would be easier to do IMAC with it (like intermediate). The Katana gets blown around to much to do IMAC in a 7mph wind, 3d is ok though Confused. Plus it is bigger and it is my first gas.
Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Tue Sep 21, 2004 9:09 pm    Post subject:  

Quote:
3Dfanatic Posted: Sun Sep 19, 2004 9:55 pm Post subject:

--------------------------------------------------------------------------------

Would you sell it airframe only?

I change my mind on that. I would for $275. But I don't want to go through shipping. I looked on the web and it is just a huge pain in the a** to ship it and package it. I saw a picture on RCU of a box 1/2 way caved in! (that was from something at fedex or ups) So.... Rolling Eyes. I don't think you would want to, but you can come and pick it up.
Back to top  
john wondra



Joined: 05 May 2004
Posts: 360
Location: auburn, wa

PostPosted: Tue Sep 21, 2004 9:18 pm    Post subject:  

sorry dude but have you looked at cheif.....its 200 for a brand new one...
_________________
John Wondra RAMS VP
Team 3D Foamy/3D Foamy Suport
__________________________
www.3dfoamy.com
www.northwest3d.com
www.e-flightline.com
www.Falconbatteries.com
www.cutimages.com <all your custom vinyl needs>
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1314
Location: Fremont, CA

PostPosted: Tue Sep 21, 2004 9:24 pm    Post subject:  

Yeah, making a crate is a pain in the butt. I made this when I shipped a 40% and cost $180 to ship it using Forward Air.


crate1.jpg
 Description:
 Filesize:  63.41 KB
 Viewed:  243 Time(s)

crate1.jpg



crate2.jpg
 Description:
 Filesize:  74.7 KB
 Viewed:  243 Time(s)

crate2.jpg



crate3.jpg
 Description:
 Filesize:  79.74 KB
 Viewed:  243 Time(s)

crate3.jpg



_________________
--Meyrick--
Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Tue Sep 21, 2004 9:56 pm    Post subject:  

Did it make it without getting the crap beat out of it?
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1314
Location: Fremont, CA

PostPosted: Wed Sep 22, 2004 5:56 am    Post subject:  

Tom Uhlendorf wrote:
Did it make it without getting the crap beat out of it?


Yep, mine made it fine. It was also insured for $5K.

_________________
--Meyrick--
Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Sun Oct 10, 2004 8:38 pm    Post subject:  

being evil being evil
Its gone. I did too low of a snap... and well you can guess the rest. DANM idea! Now its just waiting for money to get my Velox. If anyone wants the motor let me know. I can ship this one cause its not so big. I also have a OS 46fx for $40, and a Thunder Tiger GP 61 for $60.
Back to top  
-3de-



Joined: 25 Sep 2004
Posts: 81
Location: Reno----911

PostPosted: Sun Oct 10, 2004 8:44 pm    Post subject:  

Man, sorry to hear that..
frown
Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Mon Oct 11, 2004 9:20 am    Post subject:  

Thanx. But you know, it is all part of the hobby.... right.
Back to top  
 
   3DBatix Forum Index -> Buy & Sell All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive