ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

RBC Kits Laser "Shocky"
8 posts
 
   3DBatix Forum Index -> Foamies
 
Author Message
Chris



Joined: 16 Apr 2004
Posts: 263
Location: Toronto, Canada

PostPosted: Mon Sep 20, 2004 4:51 pm    Post subject: RBC Kits Laser "Shocky"  

Just flew this bad boy today and it flies sweet I only had enough batter charge for some hovering and some trimming and a little fying around btu I can say this thing hovers like hands off!


_________________
-Chris-
3D Foamy
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 916
Location: Fremont, CA

PostPosted: Mon Sep 20, 2004 9:09 pm    Post subject:  

Is this a kit from a manufacturer or your own design?
_________________
--Meyrick--
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 263
Location: Toronto, Canada

PostPosted: Tue Sep 21, 2004 11:53 am    Post subject:  

it's from RBC kits, you can get them from www.oilmanelectricrc.com tell him chris sent ya Smile I did a build up thread on RC Canada it can be found at www.rccanada.ca in the electric forum
_________________
-Chris-
3D Foamy
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 263
Location: Toronto, Canada

PostPosted: Tue Sep 21, 2004 2:22 pm    Post subject:  

*3D flight report*

The plane does all 3D moves with great success as sttated b4 the plane practically hover hands off, and that is also to be said with the torque rolls! harriers are very solid upright and inverted and inverted flight needs very little elevator if any! When bringing the plane down in an elevator wither inverted or upright it comes down very smoothly with no wing rock at all! Knife edge has a little bit of coupling but is very managed able. Thanks to the planes great harrier flight, and knife edge it makes the plane to great rollign harriers both left and right! you can make them very tight or very large without having a problem with it loosing it's form! When doing a wall it pulls up very nice and straight. Flat spins inverted or up right even blenders are done with ease with very little to no tail flex.

*Conclusion*

Appearence: 5/5
Flight: 4/5
3D Flight: 5/5
Ease of build: 5/5
Instructions: 3/5

The only main fall of these planes is the instructions. They were in german and left out some steps but I believe with the help of this thread you would have no problem putting together your laser! IF you need any further help or info don;t hesitate to give me a PM!

_________________
-Chris-
3D Foamy
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 263
Location: Toronto, Canada

PostPosted: Wed Sep 29, 2004 5:26 pm    Post subject:  

here's a vid! http://ccann.rchomepage.com/laser200.wmv please right click save as!
_________________
-Chris-
3D Foamy
Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 365
Location: Morgan Hill, CA

PostPosted: Wed Sep 29, 2004 8:00 pm    Post subject:  

How much does it weigh?
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 263
Location: Toronto, Canada

PostPosted: Thu Sep 30, 2004 3:32 am    Post subject:  

7.4oz thast with a heavier servo on ailerons (the futaba)
_________________
-Chris-
3D Foamy
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 263
Location: Toronto, Canada

PostPosted: Fri Oct 15, 2004 9:24 pm    Post subject:  

pics of my nose job on the laser cut like 1/2 the nose off put the lg back in and the wing struts. i put this thing through hell and back and the nose was getting to heavy from the glue and it was becomming less and less tail heavy and so i chopped the nose re moutned the motor the lg and struts and put some home made lettering on it for good measure :-p

pics:
http://www.rccanada.ca/bb/download.php?id=9668
http://www.rccanada.ca/bb/download.php?id=9669
http://www.rccanada.ca/bb/download.php?id=9670
http://www.rccanada.ca/bb/download.php?id=9671

_________________
-Chris-
3D Foamy
Back to top  
 
   3DBatix Forum Index -> Foamies All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive