ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

funtana muffler?
13 posts
 
   3DBatix Forum Index -> 3D Talk
 
Author Message
Rcflyer



Joined: 01 Jul 2004
Posts: 65

PostPosted: Mon Sep 20, 2004 7:51 pm    Post subject: funtana muffler?  

hello everyone iam using the satio 100 for the power plant on the
funtana 90 as most of you probly know by now,tonight we were fitting on the cowl and we are trying to decide how munch we need to cut off on the bottom where it has that flat bottoma cut out line,all of it,half of it
,etc and we are trying to decide if we should use the stock muffler and just turn it so it faces out to the side are just put a extiction on it and let it come out on the bottom. any suggestions are input on this would be greatly apprecated.
Back to top  
Shaun



Joined: 10 Sep 2004
Posts: 206
Location: texas

PostPosted: Mon Sep 20, 2004 8:28 pm    Post subject:  

I used the stock muffler. I did cut a hole larger then I wanted to. Sad
Back to top  
Shaun



Joined: 10 Sep 2004
Posts: 206
Location: texas

PostPosted: Mon Sep 20, 2004 8:40 pm    Post subject:  

I will put on a about 3" deflector and cut a hole at the very bottom of the cowl.


3.jpg
 Description:
 Filesize:  148.99 KB
 Viewed:  291 Time(s)

3.jpg


Back to top  
Shaun



Joined: 10 Sep 2004
Posts: 206
Location: texas

PostPosted: Mon Sep 20, 2004 8:42 pm    Post subject:  

from the front.


2.jpg
 Description:
 Filesize:  138.44 KB
 Viewed:  290 Time(s)

2.jpg


Back to top  
Shaun



Joined: 10 Sep 2004
Posts: 206
Location: texas

PostPosted: Mon Sep 20, 2004 8:46 pm    Post subject:  

I guess I could have turned it out, but I didn't want fuel sprayed down the side of the plane Sad


1.jpg
 Description:
 Filesize:  133.19 KB
 Viewed:  289 Time(s)

1.jpg


Back to top  
DTB



Joined: 24 Jul 2004
Posts: 139
Location: Jackson, MS

PostPosted: Tue Sep 21, 2004 9:23 am    Post subject:  

That's a very neat looking cowl, but make sure that the engine will have enough cooling. My YS 1.10FZ started to over heat until I opened up the cowl a lot more than I had it and it was open more than yours originally, but I do have a different engine than you do. Just make sure it isn't overheating.

How does you plane fly Shaun with the 100?

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
Rcflyer



Joined: 01 Jul 2004
Posts: 65

PostPosted: Tue Sep 21, 2004 12:44 pm    Post subject:  

on our extra 60 we have a extion on it and it just comes out the bottom basicaly like shaun but wiht just a little more cowl cut out ,we will probly cut out all of the bottom for sure (just to the cut outline) for cooling well still have to think about muffler,I saw a pic, think it was by dtb it showed the bottom of the plane and looked like he just turned so the exaust comes out the side and just cut a opening for the muffler to come out,didit really look that bad,i think it looked kinda good but saw 4 holes on the bottom,was that just for extra cooling?
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 139
Location: Jackson, MS

PostPosted: Tue Sep 21, 2004 2:15 pm    Post subject:  

Yea, that sounds like my cowl at first. I cut the bottom back out and place four quarter size holes, but it didn't provide enough cooling for the YS. The Saito may be different. I basically cut out the bottom now for extra cooling. My YS started detonating and running hot and lost power in the air after about 3 minutes. Now on the ground, you can't see anything but a nice looking cowl with the head sticking out, but in the air, it is open a lot more so air can flow through easier. Again, the YS may be different as for as cooling is concerned since it is more of a performance engine. My Saito 40 is a blast on my Fat Free Taco. Tons of power from that motor.
_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
Rcflyer



Joined: 01 Jul 2004
Posts: 65

PostPosted: Tue Sep 21, 2004 9:46 pm    Post subject:  

i think it turned out oky and by the way tongiht me and my dad got the cut out for the 2 radials and cut out for the needle vaulve
Back to top  
Shaun



Joined: 10 Sep 2004
Posts: 206
Location: texas

PostPosted: Wed Sep 22, 2004 4:38 am    Post subject:  

DTB- I haven't got a chance to fly it yet Crying or Very sad . I'm trying move a couple of things around so that I will not have to add any weight.
I hope the motor doesn't get to hot by the way I have the cowl cut it out!
I'll have to keep an eye on it." You got me thinking now"
I will have to open up one more hole for the exhaust to come out of in the very back bottom of the cowl, maybe I'll make it a little larger? Think
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 139
Location: Jackson, MS

PostPosted: Wed Sep 22, 2004 2:28 pm    Post subject:  

Shaun wrote:
DTB- I haven't got a chance to fly it yet Crying or Very sad . I'm trying move a couple of things around so that I will not have to add any weight.
I hope the motor doesn't get to hot by the way I have the cowl cut it out!
I'll have to keep an eye on it." You got me thinking now"
I will have to open up one more hole for the exhaust to come out of in the very back bottom of the cowl, maybe I'll make it a little larger? Think


A good rule of thumb is you want your 2-3 times more exhaust exit than intake. You are using a big motor so make sure it is running rich and has plenty of cooling.

Good luck Shaun...

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
BRADY3D



Joined: 17 Jul 2004
Posts: 2
Location: texas

PostPosted: Wed Oct 06, 2004 7:07 am    Post subject: funtana muffler  

hey Shaun out of all thing why did you have that spiner on there when we flow it
Back to top  
Shaun



Joined: 10 Sep 2004
Posts: 206
Location: texas

PostPosted: Wed Oct 06, 2004 7:40 am    Post subject:  

Well.....I would have had to cut it all up. It's just sticking on there in the picture!!
I guess it doesn't really matter though! I bought this larger aluminum spinner and I still had to trim it some Sad .
That 4 pitch prop was to flat!!
I kinda like the looks of it now. Smile



f2.jpg
 Description:
 Filesize:  135.49 KB
 Viewed:  184 Time(s)

f2.jpg



_________________
http://www.texomarc.org/
Back to top  
 
   3DBatix Forum Index -> 3D Talk All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive