ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Scratch Building an H9 Edge 540
6 posts
 
   3DBatix Forum Index -> Workshop
 
Author Message
faisalkhan67



Joined: 25 Apr 2004
Posts: 8
Location: Lahore, Pakistan

PostPosted: Fri Apr 30, 2004 11:09 am    Post subject: Scratch Building an H9 Edge 540  

Hi!

I've found some very nice pics and videos of H9 Edge onthis site. I am thing to build this from the scratch. I've done a lot of homework on this project. Collecting diagrams & 3 views, scaling it for a 78 inch span.

I want to know if u have construction fotos of ths model. Earlier there was a review section but it is now missing in this site.

Thanks

Faisal[/b]
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1178
Location: Sunnyvale, CA

PostPosted: Fri Apr 30, 2004 11:24 am    Post subject:  

so you want to scratch buld this plane? Why not just buy it as an arf? I doubt that you will find sufficient plans to build the plane from.
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
faisalkhan67



Joined: 25 Apr 2004
Posts: 8
Location: Lahore, Pakistan

PostPosted: Fri Apr 30, 2004 12:01 pm    Post subject:  

I enjoy making one as much as flying it. I made a Su-do-koi 40, Ultimate and a Pitts Eagle from scratch and these are my favs. Now I want to try designing and building big grin .

Edge is a mid wing like Extra 300. I want to know how shouls i make a wingsaddle for my one piece wing.
Back to top  
3Dfanatic



Joined: 15 Apr 2004
Posts: 300
Location: Tacoma(area), WA

PostPosted: Fri Apr 30, 2004 6:27 pm    Post subject:  

A 78" one piece wing is gonna be a BEAR to transport. Make them plug-in!
_________________
-Aaron

cutimages.com
offthewallrc.com
Back to top  
faisalkhan67



Joined: 25 Apr 2004
Posts: 8
Location: Lahore, Pakistan

PostPosted: Sun May 02, 2004 12:15 pm    Post subject:  

I have not made a two piece wing ever so a large single wing is infact an escape through a shorter route. I considered making one as it will not weaken my fuselage but since i've made it before so Rolling Eyes . Ok, these are my basic Qs.
1. How is that center tube locked in the wing halves? Any bolts required from the bottom of the wing, accross.
2. Can a light Aluminum tube (1 inch dia) work?
3. How long it should be for a 78"wing span?
4. Does the hole in the foam require some hardening with epoxy etc, so that the tube stay tight always?

Thanks
Back to top  
faisalkhan67



Joined: 25 Apr 2004
Posts: 8
Location: Lahore, Pakistan

PostPosted: Sun May 02, 2004 12:22 pm    Post subject:  

I have not made a two piece wing ever so a large single wing is infact an escape through a shorter route. I considered making one as it will not weaken my fuselage but since i've made it before so Rolling Eyes . Ok, these are my basic Qs.
1. How is that center tube locked in the wing halves? Any bolts required from the bottom of the wing, accross.
2. Can a light Aluminum tube (1 inch dia) work?
3. How long it should be for a 78"wing span?
4. Does the hole in the foam require some hardening with epoxy etc, so that the tube stay tight always?

Thanks
Back to top  
 
   3DBatix Forum Index -> Workshop All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive