ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

CD Rom Motors
19 posts
 
   3DBatix Forum Index -> Foamies
 
Author Message
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 685
Location: Sunnyvale, CA

PostPosted: Wed Dec 29, 2004 6:35 pm    Post subject: CD Rom Motors  

Decided to try makin my own brushless motor. Picked up 3 small spools of diff awg magnet wire, and found some old CD Rom drives, and pulled out the motors. After reading an article on how the motors work and how to rewind them, i got to work. First one i made was a 5 turn, 22awg speed motor. Swings a 3x2 prop and some insane RPM (on two cells). I also wound another motor at 30 turns with 30awg wire, but am having a few difficulties with that one right now. Here are some pictures. Weighs in at just under 1 oz as you see it.


PC290304.JPG
 Description:
 Filesize:  67.55 KB
 Viewed:  262 Time(s)

PC290304.JPG



_________________
Zak West
Team DA

Desert Aircraft

Smart Fly

Fromeco Avionics

Stick and Rudder Photos
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 685
Location: Sunnyvale, CA

PostPosted: Wed Dec 29, 2004 6:37 pm    Post subject:  

stator and the end bell with prop


PC290308.JPG
 Description:
 Filesize:  65.6 KB
 Viewed:  261 Time(s)

PC290308.JPG



_________________
Zak West
Team DA

Desert Aircraft

Smart Fly

Fromeco Avionics

Stick and Rudder Photos
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 685
Location: Sunnyvale, CA

PostPosted: Wed Dec 29, 2004 6:37 pm    Post subject:  

Close up of the windings.


PC290306.JPG
 Description:
 Filesize:  68.49 KB
 Viewed:  260 Time(s)

PC290306.JPG



_________________
Zak West
Team DA

Desert Aircraft

Smart Fly

Fromeco Avionics

Stick and Rudder Photos
Back to top  
TeamMoki3D



Joined: 08 Oct 2004
Posts: 430
Location: Belvidere, NJ

PostPosted: Wed Dec 29, 2004 6:57 pm    Post subject:  

sweeeeet! Cool you gonna slap it on one of your foamies? and where did u find the article on them motors?
_________________
"uhhhhhhhhh......Whoah! (uhuhuhhhuhh) I think I just figured something out...... this sucks!"
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 685
Location: Sunnyvale, CA

PostPosted: Wed Dec 29, 2004 7:19 pm    Post subject:  

RCM from October of this year has the article. I will put my low turn one in a flying wing of some sort. Im workin on one right now thats 32turn that might go in a 3mm 3D plane.
_________________
Zak West
Team DA

Desert Aircraft

Smart Fly

Fromeco Avionics

Stick and Rudder Photos
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 685
Location: Sunnyvale, CA

PostPosted: Wed Dec 29, 2004 7:23 pm    Post subject:  

During winding...two phases are done


PC290311.JPG
 Description:
 Filesize:  72.76 KB
 Viewed:  251 Time(s)

PC290311.JPG



_________________
Zak West
Team DA

Desert Aircraft

Smart Fly

Fromeco Avionics

Stick and Rudder Photos
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 924
Location: Fremont, CA

PostPosted: Wed Dec 29, 2004 8:04 pm    Post subject:  

Zak, did you steal those CD-Rom drives from your school? Mr. Green Man that looks like a lot of work. You can buy them from www.parkflyermotors.com for under $10.
_________________
--Meyrick--
Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 368
Location: Morgan Hill, CA

PostPosted: Wed Dec 29, 2004 9:44 pm    Post subject:  

Maybe I should try that. My dad "says" that he could make an ESC for brushless and make some servos too. He does this stuff for a living(he is a disc drive engineer) and says doing it is pretty cheap. So maybe I could get a foamie flying under $50 Laughing . Looks pretty fun too.
_________________
Hey Butthead! (he hehe hehehehehehehe) I figured somthing out too... (he he)I need T.P. for me bunghole! (yeah...!)
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 685
Location: Sunnyvale, CA

PostPosted: Wed Dec 29, 2004 10:04 pm    Post subject:  

yeah its pretty fun. I cant figure out what is goin wrong with my 3D motor...i know i had it wound wrong the first time, but now its just dead... Its a pain in the butt to wind 32 turns of 30awg and keep all the wires goin in the right places.
_________________
Zak West
Team DA

Desert Aircraft

Smart Fly

Fromeco Avionics

Stick and Rudder Photos
Back to top  
3Dfanatic



Joined: 15 Apr 2004
Posts: 279
Location: Tacoma(area), WA

PostPosted: Thu Dec 30, 2004 11:46 pm    Post subject:  

That's why I ordered an Axi Laughing
_________________
-Aaron

cutimages.com
offthewallrc.com
Back to top  
pattern3dflyer



Joined: 13 Oct 2004
Posts: 9

PostPosted: Fri Dec 31, 2004 9:44 am    Post subject:  

Check out http://www.gobrushless.com, they sell all kinds of parts to make all sorts of CDROM motors and they have a forum with lots of experts that have made some amazing and powerful little motors. I have already wound 2 of them for a scratch built 3D foamy.

The single stator kit wound with 20 to 23 turns of 26 AWG in a Y conf put out over 12oz of thrust on a 8X4 prop for 15 minutes on a 730mah 3C Lipo. All from a motor with prop that weighs less than an ounce and costs less than $9. Perfect for a 6 to 8 oz 3D foamy.
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 685
Location: Sunnyvale, CA

PostPosted: Fri Dec 31, 2004 10:47 am    Post subject:  

Hmm maybe i should go to 26awg. I cant get this motor to run. The most it does is sit there and make noise and jitter a bit. I think it might be the magnets.
_________________
Zak West
Team DA

Desert Aircraft

Smart Fly

Fromeco Avionics

Stick and Rudder Photos
Back to top  
3D-kid330



Joined: 14 Nov 2004
Posts: 123
Location: Fremont, Ca

PostPosted: Fri Dec 31, 2004 11:40 am    Post subject:  

Cool, are these going to be as powerful as an Axi or a Hacker? The price sounds really appealing. Laughing
_________________
Lower??!!
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 924
Location: Fremont, CA

PostPosted: Fri Dec 31, 2004 11:45 am    Post subject:  

3D-kid330 wrote:
Cool, are these going to be as powerful as an Axi or a Hacker? The price sounds really appealing. Laughing


I don't think so..

_________________
--Meyrick--
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 270
Location: Toronto, Canada

PostPosted: Fri Dec 31, 2004 12:37 pm    Post subject:  

3d kid check out www.customcdr.com their double stator is more powerful then a 2212 axi i got one of their singles on the way
_________________
-Chris-
3D Foamy
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 871
Location: Fremont, CA

PostPosted: Fri Dec 31, 2004 12:43 pm    Post subject:  

Chris wrote:
3d kid check out www.customcdr.com their double stator is more powerful then a 2212 axi i got one of their singles on the way


Hmm, I guess I was wrong. Chris, what size prop will your's be swinging?

_________________
--Meyrick--
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 259
Location: Toronto, Canada

PostPosted: Fri Dec 31, 2004 4:41 pm    Post subject:  

for the single I baught the 3d one (obviously Laughing ) and I baught some 8x6 gws slowfly props, I will also be running a prop saver on 3s and 2s 340mah 20c kokams
_________________
-Chris-
3D Foamy
Back to top  
pattern3dflyer



Joined: 13 Oct 2004
Posts: 9

PostPosted: Mon Jan 03, 2005 10:04 pm    Post subject:  

These motors definately can be as powerful as AXI's or more! www.customcdr.com is using parts from www.gobrushless.com. He is only making about $20 profit for about 1 - 2 hours of work. The double stators compare to the AXI, the single stators are great for 3D models weighing less than 8 oz.


3dbatixkid If your motor overheated you might have ruined your magnets. If it jitters you may have a bad solder connection. The gobrushless.com site has a nice troubleshooting pdf you can download. Also if you overload the motor by putting in too big a prop for the magnet strength and winds it will stop turning and make noise when you accelerate too hard. I had this happen on one when I overheated the magnets with a Monokote Heat gun trying to smooth out some JB weld. I knew better I just wasn't thinking!
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 676
Location: Sunnyvale, CA

PostPosted: Mon Jan 03, 2005 11:15 pm    Post subject:  

I may have done that since its been soldered on and i use the heat gun to shrink the shrink tubing. This motor could be junk. At least i have one that runs. Thanks for the info.
_________________
Zak West
Team DA

Desert Aircraft

Smart Fly

Fromeco Avionics

Stick and Rudder Photos
Back to top  
 
   3DBatix Forum Index -> Foamies All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive