ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Funtana Throws
7 of 9 posts archived
 
   3DBatix Forum Index -> Gear Talk
 
Author Message
El Diablo



Joined: 10 Jan 2005
Posts: 46

PostPosted: Tue Jan 18, 2005 5:44 am    Post subject: Funtana Throws  

Hey guys I finally got my radio back from JR and am setting up my Funtana. I seem to be having a control throw problem. I can't seem to get enough throw in 1 direction for all the tail surfaces . I'm not sure if I built in a mechanical advantage or what. I centered the servo's and the surfaces before I hooked up the linkages, but it still seems to have a lot more throw on 1 side of each. I'll try to get some photos up later but I thought 1 of you guys might have seen this before. Bear in mind, I haven't built a new plane in a few years, so I might just be an idiot.
_________________
If you aint crashin'... you aint pushin' the envelope.
Back to top  
Gezoid



Joined: 24 May 2004
Posts: 161
Location: UK

PostPosted: Tue Jan 18, 2005 5:59 am    Post subject:  

Yeah, my elevator servo arm is one notch off centre to get equal throw. If the movement is linear in both directions and you're getting the throw you want then just forget about it. If it works, it works. sly wink
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1178
Location: Sunnyvale, CA

PostPosted: Tue Jan 18, 2005 5:23 pm    Post subject:  

Ive found that you can attribute offset to the control horns. If both the control horns are not mounted with the pivo points DIRECTLY over the hinge line, then you will have different throws.
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
Gezoid



Joined: 24 May 2004
Posts: 161
Location: UK

PostPosted: Wed Jan 19, 2005 2:36 am    Post subject:  

Yup, that's what it is. 'bout time someone made something to hold the damn horn in position while you mark the holes. Would need a blade to fit between the surfaces or something, I dunno, it's always a problem when you're using large control surface movements. Rolling Eyes
Back to top  
El Diablo



Joined: 10 Jan 2005
Posts: 46

PostPosted: Mon Jan 24, 2005 5:55 am    Post subject: Funtana throws  

I did my best to to get those lined up right when I built it, but I rechecked 'em and they look right. The next plane I build I'll have to make a jig for 'em just to be sure. I was able to tune most of it out with the radio but I definitely need a new radio, XF622 just aint got enough features. ATF dual rates and I think 2 mixes. Pretty crummy compared to whats out there today.
_________________
If you aint crashin'... you aint pushin' the envelope.
Back to top  
El Diablo



Joined: 10 Jan 2005
Posts: 46

PostPosted: Mon Jan 24, 2005 6:03 am    Post subject: Throws  

I need some advice on my low rates. How much throw do you run for low rate on your Funtana 90's for ailerons and Elevator. I got mine up for 1 short test flight sunday eve. before my engine started getting stupid on me. It felt real twitchy even on low rates, BTW my radio doesn't have expo at all and no dual rate on rudder.
_________________
If you aint crashin'... you aint pushin' the envelope.
Back to top  
Shaun



Joined: 10 Sep 2004
Posts: 342
Location: texas

PostPosted: Mon Jan 24, 2005 7:10 am    Post subject:  

Quote:
How much throw do you run for low rate on your Funtana 90's for


I did my low rates per the instrustion manuel. Aileron 20% up and down.
My elevator is 15% up and down. both with 30% expo.
On high rayes I gave it all I could get.

It's like two diffrent planes. On low rates it flys like a trainer. but un high rates it will do whatever you want it to.It still flys great but it is ALOT more manuverable!!!

_________________
http://www.texomarc.org/
Back to top  
2 posts after this were not archived
 
   3DBatix Forum Index -> Gear Talk All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive