ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Diablo 3D birth
11 posts
 
   3DBatix Forum Index -> Foamies
 
Author Message
DTB



Joined: 24 Jul 2004
Posts: 193
Location: Jackson, MS

PostPosted: Sun Feb 06, 2005 10:11 pm    Post subject: Diablo 3D birth  

Here is my Diablo 3D that has been recently completed. All the lettering has been cut out by hand, free handed.

The plans are very good and are straight forward in general. This plane's design compared to other foamies I have seen is so much better. The plane is very solid in feel. Actual flight report is unknown to date. I received a defective Phx-25 which has to be sent back for service under warranty. The ESC actually caught fire and burned my plane a little. Patrick at Castle Creations has already been contacted about this and stated no cost for repair would occur. Gotta love a company the backs their products.

Diablo setup includes:

Himaxx 2812-0850
TP 1320 11.1V Li-poly
GWS 12x6 (gray)
Phoenix 25
Hitec Feather Rx
Hitec HS-55
Trick RC covering
"Watts Up" Watt Meter
Triton Charger
Futaba Tx
Phx-Link (can't install on my computer for some reason)

I would like to thank Meyrick for all the correspondance with me through out the build over the past couple of weeks. He is truely a nice guy and very helpful.

Thank Meyrick.

Once I get my Phx-25 back I hope to have a flight report soon after.



Diablo.jpg
 Description:
 Filesize:  48.6 KB
 Viewed:  315 Time(s)

Diablo.jpg



Diablo 2.jpg
 Description:
 Filesize:  52.61 KB
 Viewed:  315 Time(s)

Diablo 2.jpg



Diablo 3.jpg
 Description:
 Filesize:  47.66 KB
 Viewed:  315 Time(s)

Diablo 3.jpg



Diablo 4.jpg
 Description:
 Filesize:  47.82 KB
 Viewed:  315 Time(s)

Diablo 4.jpg



Diablo 5.jpg
 Description:
 Filesize:  43.92 KB
 Viewed:  315 Time(s)

Diablo 5.jpg



_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 924
Location: Fremont, CA

PostPosted: Sun Feb 06, 2005 10:19 pm    Post subject:  

Whoa, that looks awesome DTB and man I can't believe you cut those lettering by hand. Are you the human vinyl cutter? Laughing Let us know your flight report. Start the CG by putting the battery right behind the landing gear. Cool
_________________
--Meyrick--
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 193
Location: Jackson, MS

PostPosted: Tue Feb 08, 2005 4:29 am    Post subject:  

Meyrick wrote:
Whoa, that looks awesome DTB and man I can't believe you cut those lettering by hand. Are you the human vinyl cutter? Laughing Let us know your flight report. Start the CG by putting the battery right behind the landing gear. Cool


LOL...

RTF weight is 13.0oz. I believe that should be light enough for some major fun with my setup.

Bernie and Patrick at Castle Creations are sending me a new Phx-25 at no charge. Customer service at it's best.

Click here --> Diablo 3D Construction

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
Joshflies3d



Joined: 22 Dec 2004
Posts: 1
Location: Sacramento, CA

PostPosted: Wed Feb 09, 2005 10:17 pm    Post subject:  

Sweet! Looks an aawwfulll lot like a Super Star Think

Josh

_________________
Josh Glavin
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 924
Location: Fremont, CA

PostPosted: Wed Feb 09, 2005 10:38 pm    Post subject:  

Joshflies3d wrote:
Sweet! Looks an aawwfulll lot like a Super Star Think

Josh


Laughing Well the Super Star is based on the Full Scale Diablo. This plan is somewhat based on the Shockflyer Super Star but the construction is much simplified and modifications on the control surfaces and fuse. Download the plans and build it Josh, I guarantee you you will like it a lot. Very Happy

_________________
--Meyrick--


Last edited by Meyrick on Thu Feb 10, 2005 6:57 am; edited 3 times in total
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 193
Location: Jackson, MS

PostPosted: Thu Feb 10, 2005 3:58 am    Post subject:  

Joshflies3d wrote:
Sweet! Looks an aawwfulll lot like a Super Star Think

Josh


Thanks...

Do you have a link to this Super Star foamy? I only know of the Super Star trainer.

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 924
Location: Fremont, CA

PostPosted: Thu Feb 10, 2005 5:29 am    Post subject:  

Here's the Super Star.

Super Star is 31" WS, all 3mm depron. Diablo is 37" WS, 6mm depron
Super Star's ailerons are a constant cord from root to tip. Diablo's aileron is tapered.
Super Star is a 6~7 piece construction on the fuse. Diablo is a 4 piece construction on the fuse.
Diablo's fuse is extended a little from top to bottom from it's original scaled up size.

There must be at least 12% difference between the two to comply with copyright laws. The size difference alone is already 21%. Parts assembly is 100% different. Ever heard of "REVERSE ENGINEERING'? Perfectly legal. Plus it's a downloadable FREE plan (non profit). Dancing Mr. Green



superstar.jpg
 Description:
 Filesize:  39.99 KB
 Viewed:  151 Time(s)

superstar.jpg



_________________
--Meyrick--
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 193
Location: Jackson, MS

PostPosted: Thu Feb 10, 2005 8:55 am    Post subject:  

I do see the similarities between the two planes, but I think they are still different. It is obvious (to me anyway) that the Diablo is bigger with a longer and taller fuse, with less construction pieces and a more solid look (may just be me).

Honestly there isn't too much difference from any of these 3D foamies on the market today IMO that would set them apart to the point of being totally different unless it is a Zagi or something along those line, but those aren't 3D planes either. 3D foamies all have slight differences, but they all look alike to me in some form or fashion. There is only so much you can do with a working 3D airplane design.

I always tell members that haven't seen the Diablo 3D to think of a larger shock flyer or 3DX, but better made.

I do think the Diablo 3D is one of the better looking foamies on the market IMHO. Everyone at my field has a 3DX or an extra 300 and use a geared drive train which works and flys fine, but being the kind of person I am, I wanted something a little different from what everyone else already had, so I chose the Diablo 3D with a outrunner motor. True, the plane isn't 100% completely different, but with the landing gear (non-funtional) and wheel pants incorporated was enough to make me decide on this model and plus it just looks awesome. The number one thing that sold me on it was the fact that it was "FREE"! The little construction time spent was no biggie as I actually enjoy building, not repairing. LOL... Laughing

Thank again Meyrick and Mickey (I think that was his name) and any one else that helped design this nice foamy.

DTB

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 193
Location: Jackson, MS

PostPosted: Mon Feb 14, 2005 9:30 pm    Post subject:  

Meyrick wrote:
Whoa, that looks awesome DTB and man I can't believe you cut those lettering by hand. Are you the human vinyl cutter? Laughing Let us know your flight report. Start the CG by putting the battery right behind the landing gear. Cool


Meyrick, I placed my TP 1320 right behind the CF rod landing gear (not the foam landing gear). The plans state 2.0 - 2.5 inches from LE. I am only able to balance there if the battery is infront of the landing gear almost to the nose.

If the battery is behind the CF landing gear where you state, it balances about 1" past the 4mm wing rod. Where is your CG on this plane and can my plane be that tail heavy? I put everything in the stock location. The plane weighs 13.0oz RTF

BTW, I haven't gotten my ESC back yet, but I didn't think it wouldn't weigh enough to really throw the CG off a lot. Could I be wrong. I know it will add a little weight, but not too much. The 13 oz was with the ESC before I had to send it back.

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 924
Location: Fremont, CA

PostPosted: Mon Feb 14, 2005 10:38 pm    Post subject:  

My battery is right behind the landing gear foam. I don't know exactly what my CG measurement is but I know it's a bit further than the plan. You can try the stock CG per plans and see if you like it. I just thought it flew better by having the battery right behind the landing gear foam. My friend Steve also has his battery right behind the landing gear and he likes the way it flies. I kinda screwed him up on his maiden cause I told him the CG was 4" behind the leading edge of the wing. So he flew it tail heavy but was not disastrous, even when the CG was way off, it was still controllable.
_________________
--Meyrick--
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 193
Location: Jackson, MS

PostPosted: Tue Feb 15, 2005 3:38 am    Post subject:  

Meyrick wrote:
My battery is right behind the landing gear foam. I don't know exactly what my CG measurement is but I know it's a bit further than the plan. You can try the stock CG per plans and see if you like it. I just thought it flew better by having the battery right behind the landing gear foam. My friend Steve also has his battery right behind the landing gear and he likes the way it flies. I kinda screwed him up on his maiden cause I told him the CG was 4" behind the leading edge of the wing. So he flew it tail heavy but was not disastrous, even when the CG was way off, it was still controllable.


Ok great. I do like a somewhat aft CG, but I will try the CG a little forward then move back.

Thanks

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
 
   3DBatix Forum Index -> Foamies All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive