ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

GWS prop experience
15 of 16 posts archived
 
   3DBatix Forum Index -> Foamies
 
Author Message
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1316
Location: Fremont, CA

PostPosted: Sun Feb 06, 2005 10:23 pm    Post subject: GWS prop experience  

We have tried the orange, gray, and black props from GWS and for some reason the black one always comes unbalanced. It is so bad that it shakes the plane like there is no tomorrow. I have a total of 5 black props and so far 4 of them are not balanced. My friend Steve is also experiencing the same problem. I'm sticking to the orange or gray prop till I figure out what is going on.
_________________
--Meyrick--
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Mon Feb 07, 2005 4:01 am    Post subject: Re: GWS prop experience  

Meyrick wrote:
We have tried the orange, gray, and black props from GWS and for some reason the black one always comes unbalanced. It is so bad that it shakes the plane like there is no tomorrow. I have a total of 5 black props and so far 4 of them are not balanced. My friend Steve is also experiencing the same problem. I'm sticking to the orange or gray prop till I figure out what is going on.


Good information to know. I was not aware of the differences.

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
3Dfanatic



Joined: 15 Apr 2004
Posts: 300
Location: Tacoma(area), WA

PostPosted: Mon Feb 07, 2005 9:47 pm    Post subject:  

I didn't know they came in other colors haha laughing
_________________
-Aaron

cutimages.com
offthewallrc.com
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Sun Feb 27, 2005 9:49 am    Post subject: Re: GWS prop experience  

Meyrick wrote:
We have tried the orange, gray, and black props from GWS and for some reason the black one always comes unbalanced. It is so bad that it shakes the plane like there is no tomorrow. I have a total of 5 black props and so far 4 of them are not balanced. My friend Steve is also experiencing the same problem. I'm sticking to the orange or gray prop till I figure out what is going on.


I have a couple of GWS grays that were very badly unbalanced.

I flew the plane with an unbalanced prop at WOT doing a vertical and you could hear vibration coming from the plane and actually feel a loss in power doing a vertical climb.

I then used a balanced prop and ofcourse the vibration was greatly reduced even just holding the plane at WOT. However, the motor is pulling .5 - 1A more at WOT. I thought the amp draw would be less with more effieciency with a balanced prop.

Could I be wrong? or is it allowing it to spin more which pulls more amps.

_________________
Fly it hard and hover it low...

My RC Photo Page


Last edited by DTB on Sun Feb 27, 2005 10:05 am; edited 1 time in total
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 367
Location: Canada

PostPosted: Sun Feb 27, 2005 10:32 am    Post subject:  

They also have bright green props. But I will be sticking with the orange they are always balanced, Inoticed my 5 black ones were extremely unbalanced.
_________________
-Chris-
3D Foamy
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Tue Mar 01, 2005 10:52 am    Post subject:  

I have been flying the foamies now long enough to form my opinion on the GWS SF prop. The GWS SF is a great prop, but the GWS SF 12x6 just can't handle the RPM the Himaxx 2812-0850 has a WOT. I get great vertical performance while at less than WOT. At WOT, the prop is flexing so much that I can see two distinct props while feeling and hear the effieciency leaving. I can either adjust my endpoints, change props or not use WOT.

I thought also could the battery (TP 1320 11.1V & Kokam 1500 11.1V) not be able to handle the draw, but the batteries are not being pushed too far. It is still within specs of the battery.

Conclusion: GWS SF is a great prop at lower RPM which 3D flying is, but atleast for me @ WOT going vertical, the prop is spinning too fast for the prop to handle it. I get better vertical climb at slightly less than WOT which is no biggie. Saves amps also by doing that which means longer flying times.

Meyrick have you noticed this?

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 367
Location: Canada

PostPosted: Tue Mar 01, 2005 11:45 am    Post subject:  

dtb would oyu be able to move up in prop size without killing your motor, batteries, or esc?
_________________
-Chris-
3D Foamy
Back to top  
-3de-



Joined: 25 Sep 2004
Posts: 81
Location: Reno----911

PostPosted: Tue Mar 01, 2005 12:32 pm    Post subject:  

Im using an E-flight and Im a foamie noob laughing , should I be using the GWS props?
Thanks.
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Tue Mar 01, 2005 12:39 pm    Post subject:  

yeah, i used the GWS props on my eflite, but thenagain, i was using the brushless motor for it. if thats what yur using for it then get the GWS 12x6. works great for me.
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Tue Mar 01, 2005 2:58 pm    Post subject:  

Chris wrote:
dtb would oyu be able to move up in prop size without killing your motor, batteries, or esc?


I don't really think so Chris. I will try a couple of different options to find what works. Thanks for all the help here and on other threads.

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Mon Mar 07, 2005 9:08 am    Post subject:  

**Update**

I originally tried the GWS SF 12x6 with decent results at lower RPM. Once the plane went vertical at WOT or close to it as in the Diablo race video, the prop would flex and you could hear flutter and feel the efficiency leave as the pull slowed dramatically. I noticed that the GWS SF 12x6 using the Himaxx 2812-0850 would flex badly at higher RPM and two prop tips would be noticed while holding the plane.

I was in my LHS last week who carries the GWS and E-Flight props also which look very much like the GWS as well as the APC props. I noticed the E-Flight is a little stiffer than the GWS, but not as stiff as the APC and has a thicker hub area, so I bought an E-Flight 12x3.8 and an E-Flight 12x6. While purchasing the E-flight props I thought the E-flight would be too stiff to use the same size prop as the GWS (12x6).

I flew the Diablo with the E-Flight 12x3.8 first for 16.5 minutes using the full TP 1320 11.1V pack. The first thing I noticed was there was no flexing and fluttering at WOT. The prop kept it’s pitch better. With the 12x3.8, I noticed that the motor felt as if it was slipping. A slipped clutch is the best description. The throttle to hover was higher also but flew the plane fine, but had noticeably less pull out of a hover. There was a slight delay once the throttle was quickly moved to WOT.

I switch to the E-flight 12x6 with the same battery full again and noticed the RPM’s were lower, but it flew the plane so much better. The pull was restored with no delay and had no flutter also at WOT. I was able to fly for 16 mins also. The E-flight 12x6 and GWS SF 12x6 pull the same Amp and the E-Flight 12x3.8 pulled 1 Amp less than the both 12x6 props but did not have the same pull.

I would recommend trying the E-Flight 12x6 if you are using the GWS SF 12x6 prop.

DTB

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
fly boy 1



Joined: 12 Nov 2004
Posts: 286
Location: Milwaukee,WI

PostPosted: Mon Mar 07, 2005 1:00 pm    Post subject:  

Sounds sweet you guys! For your GWS props how do you cut off the Excess from the prop hub, so it is short enough to fit on the himax prop adapter? Also what are you guys using as weight to balance your E props? And DTB does the E-Flite prop have to be modified at all for it to fit on the Himax 2812-0850 prop adaptor?
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Mon Mar 07, 2005 1:51 pm    Post subject:  

fly boy 1 wrote:
Sounds sweet you guys! For your GWS props how do you cut off the Excess from the prop hub, so it is short enough to fit on the himax prop adapter? Also what are you guys using as weight to balance your E props? And DTB does the E-Flite prop have to be modified at all for it to fit on the Himax 2812-0850 prop adaptor?

to shave the prop hub, i use a skill saw and just cut the FRONT off. if you cut the back off it will be all wierd and messed up on the prop adapter.

_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Mon Mar 07, 2005 2:20 pm    Post subject:  

fly boy 1 wrote:
DTB does the E-Flite prop have to be modified at all for it to fit on the Himax 2812-0850 prop adaptor?


The E-Flight has to have the center opened up as the GWS does, but there is nothing to shave off. It will fit the prop adaptor with no problem or shaving. The hub is shorter.

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
ace dogfigter



Joined: 23 Oct 2005
Posts: 10
Location: belgiun

PostPosted: Thu Nov 17, 2005 8:41 am    Post subject:  

i used the black gws props the balacing was so poor that one prop wackt the nose of my plane of mad i bought 3 and the were al very bad now i use graupner slofly props they work great big grin
Back to top  
1 post after this was not archived
 
   3DBatix Forum Index -> Foamies All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive