ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Diablo and APC props???
4 posts
 
   3DBatix Forum Index -> Foamies
 
Author Message
POWER



Joined: 07 Feb 2005
Posts: 5

PostPosted: Tue Feb 08, 2005 2:05 pm    Post subject: Diablo and APC props???  

Hi all, I have been reading a lot about the use of the GWS 12-6SF with the AXI 2212-34 on the Diablo. The video is impressive to say the least. Has anyone used the APC 12-6?

Everything I read about the AXI says the 12-6 will be pushing the motor too hard, but if it draws 11 amps or under it should stay cool under 3D conditions. I sold a 2212-34 about 6 months ago because I was under the impression the 11-4.7 was the max prop for the motor. Now I have another one sitting in front of me Rolling Eyes

POWER
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 902
Location: Fremont, CA

PostPosted: Tue Feb 08, 2005 2:37 pm    Post subject: Re: Diablo and APC props???  

POWER wrote:
Hi all, I have been reading a lot about the use of the GWS 12-6SF with the AXI 2212-34 on the Diablo. The video is impressive to say the least. Has anyone used the APC 12-6?

Everything I read about the AXI says the 12-6 will be pushing the motor too hard, but if it draws 11 amps or under it should stay cool under 3D conditions. I sold a 2212-34 about 6 months ago because I was under the impression the 11-4.7 was the max prop for the motor. Now I have another one sitting in front of me Rolling Eyes

POWER


The 221234 is a lower RPM, higher torq motor compared to the 221226. So you will get better performance with the 12-6 prop. Zak hooked up an Astroflight watt meter on a 221234 with GWS 12-6 prop and it was reading 13amps at full throttle. The Thunder power 1320mah 3 cells are rated @ 15-18amps so you're safe.

As far as APC props, their too stiff and you get less efficiency. I've used it and it drains the battery faster than the GWS props and it does not perform any better.

_________________
--Meyrick--
Back to top  
POWER



Joined: 07 Feb 2005
Posts: 5

PostPosted: Fri Feb 11, 2005 5:23 am    Post subject:  

Meyrick, the red and blue Diablo in the video. What prop? I have seen the APC 12-3.8 mentioned. I have a pile of 12-6GWS props, but if I can lower the amp draw a bit and still get performance like the video displays I will try the APC, Thanks!!


POWER
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 902
Location: Fremont, CA

PostPosted: Fri Feb 11, 2005 7:39 am    Post subject:  

POWER wrote:
Meyrick, the red and blue Diablo in the video. What prop? I have seen the APC 12-3.8 mentioned. I have a pile of 12-6GWS props, but if I can lower the amp draw a bit and still get performance like the video displays I will try the APC, Thanks!!


POWER


That one is using the GRAY GWS 12x6 prop.

_________________
--Meyrick--
Back to top  
 
   3DBatix Forum Index -> Foamies All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive