ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Wanted 5 Hitec MG servos
14 posts
 
   3DBatix Forum Index -> Buy & Sell
 
Author Message
paulaly



Joined: 16 Feb 2005
Posts: 36

PostPosted: Fri Feb 18, 2005 9:29 pm    Post subject: Wanted 5 Hitec MG servos  

I am looking for 5 Hitec metal gear servos to put in a Funtana 90. I am buying a 9CAF but I think the servos are not up to the job.
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1178
Location: Sunnyvale, CA

PostPosted: Fri Feb 18, 2005 11:08 pm    Post subject:  

get a radio with some high tork servos. I beleive you can get the radio with any servo if you order from Futaba or Tower.
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
paulaly



Joined: 16 Feb 2005
Posts: 36

PostPosted: Sat Feb 19, 2005 9:38 am    Post subject:  

Thanks for the reply Zak. The problem with that one is that my wife has ordered it from a hobby store in Calgary, Canada. But if they could do that as I will call today, would you reccomend MG all the way or will hi torque plastic gears do? I am a bit courious on plastic as I had one go on my aeileron with my H9 Twist. Which hi torque are you thinking of?

Thanks
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1178
Location: Sunnyvale, CA

PostPosted: Sat Feb 19, 2005 12:30 pm    Post subject:  

I would go metal gears. The 9402s are great servos. They will run you almost 100 a piece though, unless you find a killer deal on them somewhere. A lot of people have been happy with Hitec MG servos as well.
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Sat Feb 19, 2005 7:39 pm    Post subject:  

or, you could just get some HITEC 645MG's 134oz tork a piece and metal gears. theyre like 45 bucks-50 bucks
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
paulaly



Joined: 16 Feb 2005
Posts: 36

PostPosted: Sun Feb 20, 2005 5:14 pm    Post subject:  

Thanks for the info I think I am going to get the HS 645 MG's. They seem to be right for this.
Back to top  
El Diablo



Joined: 10 Jan 2005
Posts: 46

PostPosted: Sun Feb 20, 2005 10:42 pm    Post subject: Hitec 645's  

A buddy of mine has 645's in a few of his birds, but I wonder if they are fast enough for a Funtana to really fly well.
_________________
If you aint crashin'... you aint pushin' the envelope.
Back to top  
paulaly



Joined: 16 Feb 2005
Posts: 36

PostPosted: Sun Feb 20, 2005 11:18 pm    Post subject:  

the 645's in Kyle's vid seem to be quick enough. Saying that I don't have the skill of Kyle but I am on a tight budget, so I think I'm gonna have to. They should be quick enough for my needs. Sorry I am not saying that your wrong.
Back to top  
JMarden



Joined: 29 Jan 2005
Posts: 58
Location: Merrick, NY, USA

PostPosted: Mon Feb 21, 2005 12:23 pm    Post subject:  

I think the best cheap set-up is the following..John Banks has had very good luck with this set-up..
Futaba 3010's on the Elevators
Hitec 645MG's on the ailerons
Hitec 645MG on the Rudder
And a Hitec 81 micro on the throttle.

Works great as far as the videos!

_________________
-Jared Marden

www.3dfoamy.com
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Mon Feb 21, 2005 2:03 pm    Post subject:  

hmmm, im not too sure about that single 645 on the rudder. i would go with an 8411 or 8611.
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Mon Feb 21, 2005 4:14 pm    Post subject:  

ohhhhhhh, cheap setup, nvm then big grin
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
El Diablo



Joined: 10 Jan 2005
Posts: 46

PostPosted: Mon Feb 21, 2005 8:19 pm    Post subject:  

Well I'm gonna upgrade my servos do to poor centering and slop. From Servo city the Hitec 645MG's are 133oz. & .20 @ 6 volts for 39.99 each.
The 5625 Digitals are 131oz. & .14 @ 6 volts for 54.99 each, 15% off if you buy 4 or more. Thats 46.75 each. Less than 7 bucks more and 30% faster.

_________________
If you aint crashin'... you aint pushin' the envelope.
Back to top  
red7fifty



Joined: 26 Mar 2005
Posts: 8
Location: Pittsburg CA

PostPosted: Sat Mar 26, 2005 8:54 pm    Post subject:  

If anyone is interested, I have 6 Futaba S-9402's
Here is my ad on RCU:
http://www.rcuniverse.com/market/item.cfm?itemID=86956
Thanks
Ernie
Back to top  
Ramz



Joined: 05 Nov 2004
Posts: 55
Location: New Brunswick, Canada

PostPosted: Sat Mar 26, 2005 9:25 pm    Post subject: hitec  

If i were you i'd go with 5625's. I'm gettin a 33% H9 Edge and i'm going with 5925's on everything but the rudder and throttle. On the rudder i'm runnin 2 5995's. For my F90 i'm gonna go with 5625's rather than 5645's. The 45's are torquier but i'd rather sacrafice a bit of torque for a bit of speed. I find when your trying to do precise maneuvers or wild 3D, a fast servo really helps. Just my .02. And i would suggest running them on 6V.
Back to top  
 
   3DBatix Forum Index -> Buy & Sell All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive