ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Spinner for a Funtana 90?
5 posts
 
   3DBatix Forum Index -> Buy & Sell
 
Author Message
Ramz



Joined: 05 Nov 2004
Posts: 55
Location: New Brunswick, Canada

PostPosted: Sat Mar 26, 2005 9:22 pm    Post subject: Spinner for a Funtana 90?  

Hey guys. I'm looking for a nice spinner for a Funtana 90. It's got a YS110 and i'm looking for an aluminum spinner that will bolt right on with no mods and that will have lots of room for a wide range or props. What are you guys using? got any pics? Thanks.
Back to top  
fly boy 1



Joined: 12 Nov 2004
Posts: 286
Location: Milwaukee,WI

PostPosted: Sun Mar 27, 2005 6:29 am    Post subject:  

The one that would work well would be the tru turn 2.5 inch aluminum spinner. Make sure that it is the wide blade version though. sly wink
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Sun Mar 27, 2005 7:48 am    Post subject:  

if your gonna go aluminum, go with Vortec. they are way cheaper than Tru-Turn. you can also get the Vortecs cut for MenZ(or wide) which you will need.
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Sun Mar 27, 2005 5:56 pm    Post subject:  

fly boy 1 wrote:
The one that would work well would be the tru turn 2.5 inch aluminum spinner. Make sure that it is the wide blade version though. sly wink


I use a 2.5" Tru-Turn wide on my FT90 with a YS 1.10FZ. I started with a APC 16x4W and now I use a APC 16x6 with no problem. The 6 degree pitch is the most you can use with the wide version.

The photos below are photos with the APC 16x4W. The APC 16x6 is better for the YS 1.10FZ IMO.



IMG_2635.JPG
 Description:
 Filesize:  70.07 KB
 Viewed:  155 Time(s)

IMG_2635.JPG



IMG_2633.JPG
 Description:
 Filesize:  152.81 KB
 Viewed:  155 Time(s)

IMG_2633.JPG



IMG_2638.JPG
 Description:
 Filesize:  65.19 KB
 Viewed:  155 Time(s)

IMG_2638.JPG



_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
Ramz



Joined: 05 Nov 2004
Posts: 55
Location: New Brunswick, Canada

PostPosted: Sun Mar 27, 2005 6:53 pm    Post subject: thanks.  

Thanks for the pics. I'll probably go Tru-Turn as i'll be running a 16x4 or a 16x6 prop. I looked at the VorTech ones and the cutouts for the prop blades look way too small for any descently sized prop, such as a 16x6.
Back to top  
 
   3DBatix Forum Index -> Buy & Sell All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive