ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

New to foamies - need a bit of help
7 posts
 
   3DBatix Forum Index -> Foamies
 
Author Message
markymark



Joined: 06 Apr 2005
Posts: 14

PostPosted: Wed Apr 06, 2005 5:03 am    Post subject: New to foamies - need a bit of help  

Hi Guys,

I'm new to the whole foamie craze and am loving the couple I have built. My question is one of understanding speed controllers.

I don't understand how to work out what Amp 'rated' speed controller I need.

Is it related purely to the motor or is the battery a factor in working it out (other than the obvious can it handle 3 cells etc)

Say I want to buy an AXI 2212/34, the motor spec says that the Max Loading is 10A. Does this mean I simply need a speed controller with a max loading of 10A and anything above is an overkill??

Also, how do I ensure the motor's 10A max is never exceeded??

Any help is appreciated!

Rgds,
Mark
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1303
Location: Fremont, CA

PostPosted: Wed Apr 06, 2005 7:01 am    Post subject:  

The prop is also a big factor. Using the AXI-22/12/34 with a 12x6 prop can draw as much as 15amps or higher.
_________________
--Meyrick--
Back to top  
markymark



Joined: 06 Apr 2005
Posts: 14

PostPosted: Wed Apr 06, 2005 10:03 am    Post subject:  

That's what I don't understand!

If the motor is rated at 10A, how can you run a 12x6 prop drawing 15A without smoking the motor?!?
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1303
Location: Fremont, CA

PostPosted: Wed Apr 06, 2005 10:36 am    Post subject:  

markymark wrote:
That's what I don't understand!

If the motor is rated at 10A, how can you run a 12x6 prop drawing 15A without smoking the motor?!?


I don't understand it either but that's what the watt meter shows... sly wink My motor is still running strong and must have over 200 flights on it with the 12x6 prop.

_________________
--Meyrick--
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1028
Location: Sunnyvale, CA

PostPosted: Wed Apr 06, 2005 3:09 pm    Post subject:  

A motor does not really have an amp rating. The motor will pull as many amps as it can until it overheats or something breaks. changing the load on the motor is the biggest way to change the amount of amps it draws. When a motor says it will pull 10 amps, that is with the reccomended prop and speed control.
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
markymark



Joined: 06 Apr 2005
Posts: 14

PostPosted: Thu Apr 07, 2005 11:01 am    Post subject:  

Hi Zak,

Well I'm building a Foame II after seeing your video and want to put the Axi 2212/34 on it. Just want to know what Amp rating speed controller is OK. Would a CastleCreations Phoenix 10 be OK or do I need a higer rated controller? What did you use on the model in the video?

mark
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1303
Location: Fremont, CA

PostPosted: Thu Apr 07, 2005 11:23 am    Post subject:  

markymark wrote:
Hi Zak,

Well I'm building a Foame II after seeing your video and want to put the Axi 2212/34 on it. Just want to know what Amp rating speed controller is OK. Would a CastleCreations Phoenix 10 be OK or do I need a higer rated controller? What did you use on the model in the video?

mark


I'll answer for Zak. The PHX10 is too small for the 2212/34. It will run but you will be limited from its full performance and you may burn up the ESC. The PHX25 is more suitable for the motor. The Foame IIx on that vid belongs to Steve and he has a PHX25 on it. Zak would probably use a Cool Runnings 25 on his.

_________________
--Meyrick--
Back to top  
 
   3DBatix Forum Index -> Foamies All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive