ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Self Destructed 2812-0850
15 of 31 posts archived
 
   3DBatix Forum Index -> Foamies
 
Author Message
DTB



Joined: 24 Jul 2004
Posts: 449
Location: Jackson, MS

PostPosted: Sat Apr 16, 2005 12:41 pm    Post subject: Self Destructed 2812-0850  

I was flying my Diablo 3D today as usual while showing a friend the plane and what it is capable of doing. All of a sudden while in level flight, the motor self destructed. Literally, the motor failed in flight. Luckily, I was able to land the plane with only minor damage. There has been no crash or any other damage to the motor since building the plane. The rear fitting seems to have failed and let go. The only things that held the motor attached to the plane were the wires leading to the Phx 25. I thought the motor mount had come undone at first until I saw exactly what happened.

I'm not the type to jump to say "defect", but this seems clearly a defective item. The self destruction action caused damage to one contact wires internally. The insulation was cut and severed contact with the motor so the motor no longer works now

Has anyone had any problems with the Himaxx 2812-0850 doing this?

I plan to contact Himaxx about this.



Self Destructed 2812-0850.JPG
 Description:
 Filesize:  93.15 KB
 Viewed:  788 Time(s)

Self Destructed 2812-0850.JPG



_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
redryder



Joined: 09 Apr 2005
Posts: 26
Location: Melbourne, Australia

PostPosted: Sat Apr 16, 2005 1:37 pm    Post subject:  

Has the motor done much flying? I'd say the gyroscopic force of the prop during manuveurs combined with a rear mount might have stretched the aluminium to the point that the stator came loose. There also appears to be some repairs on the fuse x-piece.

Good you got the plane down in one piece.

red
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 449
Location: Jackson, MS

PostPosted: Sat Apr 16, 2005 1:49 pm    Post subject:  

redryder wrote:
Has the motor done much flying? I'd say the gyroscopic force of the prop during manuveurs combined with a rear mount might have stretched the aluminium to the point that the stator came loose. There also appears to be some repairs on the fuse x-piece.

Good you got the plane down in one piece.

red


I fly when I can. I did a maiden on 02/23/05. So it has almost been 2 months since I started flying it. The x-piece damage came from trying the prop saver attachment and it came off and the prop hit the foam, but it didn't hurt the motor, so I went back to the prop adaptor which works better for me. That was 2 months ago almost when I got the motor. The motor/prop hit the fuse again today and prop hit the x-piece again which is why it looks worst.

_________________
Fly it hard and hover it low...

My RC Photo Page


Last edited by DTB on Sat Apr 16, 2005 2:00 pm; edited 1 time in total
Back to top  
redryder



Joined: 09 Apr 2005
Posts: 26
Location: Melbourne, Australia

PostPosted: Sat Apr 16, 2005 2:00 pm    Post subject:  

Ok, so it's had a bit of flying. Have you tried putting the motor back together? If so, does it feel at all loose?

red
Back to top  
Adam Neat



Joined: 11 Apr 2005
Posts: 14
Location: Winchester Ohio

PostPosted: Sat Apr 16, 2005 2:08 pm    Post subject:  

Hopefully Himaxx will stand behind it and give you a new one. I wonder if something like this is what caused them to change the design a little like they did.

Let us know how it turns out.

Adam
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 449
Location: Jackson, MS

PostPosted: Sat Apr 16, 2005 2:14 pm    Post subject:  

redryder wrote:
Ok, so it's had a bit of flying. Have you tried putting the motor back together? If so, does it feel at all loose?

red


The magnest are still in the same place. The rear section is what let go. The blue wire is not connected to the wires anymore. I haven't put it together again and probably won't. I will leave it like it is until I hear from Himaxx. These motors have a 2 year warranty and I didn't start flying with it until 02/23/05 which is very far from being close to 2 years. I looked closer to the rear section and it is threaded, but we can't tighten or loosen the thread once it is built. This is tighten during the construction of the motor. Once built, the three wires inside connecting to the motor will prevent it from turning unless you twist the wires alot. I am starting to think the motor wasn't tighten completely originally. Look at the photo above and you will see the threads which screws into the rear section, but the three wires will have to be twisted heavily to turn the full threads and tighten.

_________________
Fly it hard and hover it low...

My RC Photo Page


Last edited by DTB on Sat Apr 16, 2005 2:17 pm; edited 1 time in total
Back to top  
JR.Master



Joined: 07 Nov 2004
Posts: 462
Location: San Angelo

PostPosted: Sat Apr 16, 2005 2:17 pm    Post subject:  

well get you another one dude since you've got the warranty big grin
_________________
Did I do that? Hummmmmm!Yep, sure did!
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 449
Location: Jackson, MS

PostPosted: Sat Apr 16, 2005 2:22 pm    Post subject:  

Adam Neat wrote:
Hopefully Himaxx will stand behind it and give you a new one. I wonder if something like this is what caused them to change the design a little like they did.

Let us know how it turns out.

Adam


Very good question. I can see how the larger rear section will allow more room to tighten if that is/was the problem.

I'll let you all know what happens.

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
redryder



Joined: 09 Apr 2005
Posts: 26
Location: Melbourne, Australia

PostPosted: Sat Apr 16, 2005 3:28 pm    Post subject:  

I can see the threads. It shouldn't have come out. Even loctite wouldn't help it to stay put because it doesn't stick well to anodised aluminium. Good luck with Himaxx.

red
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1312
Location: Fremont, CA

PostPosted: Sat Apr 16, 2005 7:10 pm    Post subject:  

Wow! Shocked Let us know what Himax says about this.
_________________
--Meyrick--
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 449
Location: Jackson, MS

PostPosted: Sat Apr 16, 2005 8:47 pm    Post subject:  

Meyrick wrote:
Wow! Shocked Let us know what Himax says about this.


Will do Meyrick..

I looked even closer at the motor again and I was wrong about the screwed in part. There is a thread design on the rear ball bearing assembly, but it is press fit onto the motor which is where it pulled apart and does not screw into place as I thought it did. The press fit came out. I thought that would have been hard to do, but obviously not. I read on other threads where others have been having this problem also, so I am not just an isolated incident.

Himaxx may have changed the rear section due to this since I have the original design with the smaller tail section. I'd rather have the new design to help with cooling anyway.

I'll post more when I get new info.

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
redryder



Joined: 09 Apr 2005
Posts: 26
Location: Melbourne, Australia

PostPosted: Sat Apr 16, 2005 10:28 pm    Post subject:  

Make up your mind. Either it is threaded or a press fit. Not both. I won't help you with anything else. Mad

red
Back to top  
redryder



Joined: 09 Apr 2005
Posts: 26
Location: Melbourne, Australia

PostPosted: Sat Apr 16, 2005 10:40 pm    Post subject:  

Let's look at this seriously. Is it any wonder manufacturers avoid even genuine warranty claims when you get stuff like this. DTB, you did not even know what you had. So Himaxx reads this. Next time someone has a real claim they'll stonewall. How have you helped the hobby? Please know your facts before you go on record.

Not happy,

red
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 449
Location: Jackson, MS

PostPosted: Sun Apr 17, 2005 5:03 am    Post subject:  

redryder wrote:
Make up your mind. Either it is threaded or a press fit. Not both. I won't help you with anything else. Mad

red


redryder wrote:
Let's look at this seriously. Is it any wonder manufacturers avoid even genuine warranty claims when you get stuff like this. DTB, you did not even know what you had. So Himaxx reads this. Next time someone has a real claim they'll stonewall. How have you helped the hobby? Please know your facts before you go on record.

Not happy,

red


Wow redryder, you took this personally didn't you and what are you flaming me for? I wasn't asking you to fix anything and I didn't design this item, so why would need to know how it is made internally? That's the reason I paid Himaxx. I didn't do anything wrong and just because you got upset doesn't change anything. The facts are still the same. The rear ball bearing has threads around it (see photo below), which I thought screwed into the rear section which was logical for me or anyone else for that matter to think so, but I later looked closer at the rear section and noticed the rear section has no teeth to accept threads. It is smooth in there, so although the ball bearing has a threaded pattern or thread type pattern on it's outside, it is still press fit into the rear section.

So redryder, you are wrong on this one and it is both.
Thanks for all your help up to this point and I didn't know I was the down fall of the RC community as a whole.



IMG_3968.JPG
 Description:
 Filesize:  77.99 KB
 Viewed:  704 Time(s)

IMG_3968.JPG



IMG_3970.JPG
 Description:
 Filesize:  101.72 KB
 Viewed:  704 Time(s)

IMG_3970.JPG



IMG_3971.JPG
 Description:
 Filesize:  112.24 KB
 Viewed:  704 Time(s)

IMG_3971.JPG



IMG_3969.JPG
 Description:
 Filesize:  140.98 KB
 Viewed:  704 Time(s)

IMG_3969.JPG



_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 449
Location: Jackson, MS

PostPosted: Sun Apr 17, 2005 9:48 am    Post subject:  

I spoke with a friend of mine who is a enginner who stated that the thread pattern are not threads but are press rings (still looks like threads to me) which are commonly used when press fit items are put together. My friend stated that they place adhesive around the item which allows it to stick better.

My motor had some sort of adhesive on the rings but not much at all. I don't expect to have any problems with Himaxx replacing it. I just don't want to wait for 2 months to receive a replacement, but I guess that is better than nothing.

I'll keep everyone posted about this.

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
16 posts after this were not archived
 
   3DBatix Forum Index -> Foamies All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive