ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

How to select a prop. size??
5 posts
 
   3DBatix Forum Index -> Foamies
 
Author Message
Dado



Joined: 22 Apr 2005
Posts: 6
Location: Slovenia, Maribor

PostPosted: Wed Jun 08, 2005 9:46 am    Post subject: How to select a prop. size??  

Guys, you are my only help. Maybe this is not the type of question for this forum, but i dont have a choice.
Where can i find what prop. is needed for particular motor and plane?

I want to put AXI 2212/34 with Lipo 1250 mAh on my ZagiKiller
http://www.aerodesign.de/modelle/HS/hs61v2.htm
and i dont know, whic prop. size is the best for this wing and motor!

can somebody help me, i would appreciate very much. If you could teach me how and where to look.

David
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 454
Location: Jackson, MS

PostPosted: Wed Jun 08, 2005 10:23 am    Post subject: Re: How to select a prop. size??  

Dado wrote:
Guys, you are my only help. Maybe this is not the type of question for this forum, but i dont have a choice.
Where can i find what prop. is needed for particular motor and plane?

I want to put AXI 2212/34 with Lipo 1250 mAh on my ZagiKiller
http://www.aerodesign.de/modelle/HS/hs61v2.htm
and i dont know, whic prop. size is the best for this wing and motor!

can somebody help me, i would appreciate very much. If you could teach me how and where to look.

David


David for the AXI 2212/34 you can 2-3 Li-Poly cells, but you didn't indicate which you had. The manufactor says to keep the Amps to 10A for no longer than 60 secs. 740 RPM/V. Max current 10 amps.

I'm sure you will not be 3D flying the plane so you won't need a huge prop (12"), but I'm not 100% sure which you will like the best either for the Zagi. For a 47.2" wingspan plane that weighs from 1.1 to 1.98 lbs, I would say to try different props no higher than a 11x7 to get the best feel for your taste. You may want a smaller diameter with more pitch to have more top speed also.

See the link below for the props and # of cells used:
Click HERE...

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
Dado



Joined: 22 Apr 2005
Posts: 6
Location: Slovenia, Maribor

PostPosted: Wed Jun 08, 2005 12:26 pm    Post subject:  

Im so happy to se a reply for my problems. I have KOKAM AKKUPACK 1250HD-3S 15C 11,1V.
Informations about my LiPos are here:
http://www.der-schweighofer.at/web/productdetails.php?artikelnummer=57143&prodID=354

I did a research for any information about prop size on AXI 2212/34 and found this:
http://www.der-schweighofer.at/pdf/axi2208_2212.pdf
It says: model weight 300-700 g
prop. range: 2xLi 12'x8'
3xLi 10'x5'
I could easily go with 10x5 prop?
12x8 is too large for this model and probably only for 3D flying, and like you said, i wont go verticaly and do hovering with Zagi. Just want to go faster to accelerate blood in my veins. big grin
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 454
Location: Jackson, MS

PostPosted: Wed Jun 08, 2005 5:17 pm    Post subject:  

Dado wrote:
Im so happy to se a reply for my problems. I have KOKAM AKKUPACK 1250HD-3S 15C 11,1V.
Informations about my LiPos are here:
http://www.der-schweighofer.at/web/productdetails.php?artikelnummer=57143&prodID=354

I did a research for any information about prop size on AXI 2212/34 and found this:
http://www.der-schweighofer.at/pdf/axi2208_2212.pdf
It says: model weight 300-700 g
prop. range: 2xLi 12'x8'
3xLi 10'x5'
I could easily go with 10x5 prop?
12x8 is too large for this model and probably only for 3D flying, and like you said, i wont go verticaly and do hovering with Zagi. Just want to go faster to accelerate blood in my veins. big grin


That sounds good. 10x5-7 should work fine. Use an amp meter to check the draw.

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
Dado



Joined: 22 Apr 2005
Posts: 6
Location: Slovenia, Maribor

PostPosted: Thu Jun 09, 2005 6:08 am    Post subject:  

Thanx DTB for help, i realy appreciate. I will try 10x5, and see the results.
Thanx again.
Back to top  
 
   3DBatix Forum Index -> Foamies All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive