ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Zak's Shock Flyer Edge set-up?
15 posts
 
   3DBatix Forum Index -> Foamies
 
Author Message
Flyerdude



Joined: 27 Aug 2004
Posts: 11
Location: Washington Twp , New Jersey

PostPosted: Thu Jun 30, 2005 4:41 pm    Post subject: Zak's Shock Flyer Edge set-up?  

Hey Zak,

What is the set-up of your shock flyer edge?

Mine is:

AXI 2208/34
Kokam 340mah pack
Hitec hs-55
Micro 555 reciever

How do you think this will fly?

-Matt
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1124
Location: Sunnyvale, CA

PostPosted: Thu Jun 30, 2005 5:00 pm    Post subject:  

Thats perfect dude. Thats a good indoor setup if you can keep it from goin through the ceiling. Try the TP 480s (one of the best cells that TP has) and the 730s as well. If you want a KILLER outdoor battery, get a Tanic 830mah. (these are all 3 cell packs). I run the 26 turn motor on mine is the only difference. I actually need to go out and buy a shock flyer and trace it out so i can mod it. The new pre cut ones kinda suck since...well..they are precut! I wanna cut my own surfaces! The one thats in the night time video was a KILLER plane cause it was all modded.
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
Flyerdude



Joined: 27 Aug 2004
Posts: 11
Location: Washington Twp , New Jersey

PostPosted: Thu Jun 30, 2005 5:03 pm    Post subject:  

Thanks for the quick reply!

What exactly did you do to the shocky to mod it?
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1124
Location: Sunnyvale, CA

PostPosted: Thu Jun 30, 2005 5:10 pm    Post subject:  

Bigger ailerons and elevator. I would have made the rudder bigger too but its already cut. I plan to make one that has all the surfaces modded. They fly GREAT with bigger surfaces.
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
Flyerdude



Joined: 27 Aug 2004
Posts: 11
Location: Washington Twp , New Jersey

PostPosted: Thu Jun 30, 2005 5:14 pm    Post subject:  

Thanks for the help and quick replies, greatly appreciated.


-Matt
Back to top  
Flyerdude



Joined: 27 Aug 2004
Posts: 11
Location: Washington Twp , New Jersey

PostPosted: Sat Jul 02, 2005 3:34 pm    Post subject:  

Another Question,

Should I leave the landing gear off, or put it on?

Are they worth the weight?


-Matt



P.S. Anyone else feel free to reply.
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1124
Location: Sunnyvale, CA

PostPosted: Sat Jul 02, 2005 7:44 pm    Post subject:  

If you are flying somewhere that has a place where you can land (even on a rare occasion) go ahead and put them on. I put the LG on all of mine, and have gotten planes down to under 6oz (diff radio setup though). With your motor and battery and all that, you are looking at about 8.5-9 oz with the LG. That will be a perfect weight. You might want to take the case off the receiver, that will offset the weight of the LG.
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
Batix Kid



Joined: 07 Apr 2005
Posts: 86

PostPosted: Sun Jul 03, 2005 9:56 am    Post subject:  

For the sake of that little bit of extra weight i would put it on anyday,it has saved my plane hundred of times lol hard landings..ect ...
Back to top  
Flyerdude



Joined: 27 Aug 2004
Posts: 11
Location: Washington Twp , New Jersey

PostPosted: Sun Jul 03, 2005 3:49 pm    Post subject:  

How would I go about taking off the case of the micro 555?

Would it be ok? I'm just not sure if it would still work?

If so, is there anything I should do to it after I take the case off?

such as shrink tube?

-Matt
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1124
Location: Sunnyvale, CA

PostPosted: Sun Jul 03, 2005 10:39 pm    Post subject:  

on the front (i think the front) of the receiver, you will see two lil slots. These slots have tabs snapped into them. Take two small flat screw drivers, and push (gently) the tabs in. You will then be able to lift the top of the case off. (also make sure there are no stickers over where the case splits) You can then shrink wrap it, or just stick it on the plane. The case does not effect how it will work, so it should be good. The shrink wrap will keep the dust out, which is nice. Hope this helps.
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
sethslasher



Joined: 23 Oct 2004
Posts: 105
Location: Ohio

PostPosted: Mon Jul 04, 2005 3:30 pm    Post subject:  

on my edge i have an axi 2208/34
GWS pico servos
duralite eplus silver 860 mah
jeti 12 amp esc
without the batt it weighs 5.5 oz. w/ gear

for better indoor flying go with the axi 2204/54
almost as great vertical as the 2208/34

_________________
Push yourself; it's just an airplane!
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1124
Location: Sunnyvale, CA

PostPosted: Mon Jul 04, 2005 9:44 pm    Post subject:  

the 2204/54 doesnt have as much power as the 2208/34 by any means. It is a good indoor motor however. I ran mine with an 8x4.3 prop and TP 480. This was about a 6.3oz setup. I actually like the planes closer to 8oz, with a bigger motor, even for indoor.
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
john wondra



Joined: 05 May 2004
Posts: 360
Location: auburn, wa

PostPosted: Tue Jul 05, 2005 2:33 pm    Post subject:  

Im calling serious BS on that...holly god no way.

I had one with a little screamer, kokam 340 3s1p pico servos and a gws RX and it still weighed 6 ox. your plane is 7-8 if not more.

sethslasher wrote:
on my edge i have an axi 2208/34
GWS pico servos
duralite eplus silver 860 mah
jeti 12 amp esc
without the batt it weighs 5.5 oz. w/ gear

for better indoor flying go with the axi 2204/54
almost as great vertical as the 2208/34

_________________
John Wondra RAMS VP
Team 3D Foamy/3D Foamy Suport
__________________________
www.3dfoamy.com
www.northwest3d.com
www.e-flightline.com
www.Falconbatteries.com
www.cutimages.com <all your custom vinyl needs>
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1124
Location: Sunnyvale, CA

PostPosted: Tue Jul 05, 2005 9:25 pm    Post subject:  

john wondra wrote:
Im calling serious BS on that...holly god no way.

I had one with a little screamer, kokam 340 3s1p pico servos and a gws RX and it still weighed 6 ox. your plane is 7-8 if not more.

sethslasher wrote:
on my edge i have an axi 2208/34
GWS pico servos
duralite eplus silver 860 mah
jeti 12 amp esc
without the batt it weighs 5.5 oz. w/ gear

for better indoor flying go with the axi 2204/54
almost as great vertical as the 2208/34


He said without battery

_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
john wondra



Joined: 05 May 2004
Posts: 360
Location: auburn, wa

PostPosted: Wed Jul 06, 2005 7:42 am    Post subject:  

o sorry i just read the specs and he listed battery and i was like no way in hell.
_________________
John Wondra RAMS VP
Team 3D Foamy/3D Foamy Suport
__________________________
www.3dfoamy.com
www.northwest3d.com
www.e-flightline.com
www.Falconbatteries.com
www.cutimages.com <all your custom vinyl needs>
Back to top  
 
   3DBatix Forum Index -> Foamies All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive