ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Variable Pitch or Vicious Problems?
11 posts
 
   3DBatix Forum Index -> Gear Talk
 
Author Message
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1178
Location: Sunnyvale, CA

PostPosted: Thu Jul 14, 2005 7:14 pm    Post subject: Variable Pitch or Vicious Problems?  

Many of you have seen the VP setups from either Shulman Aviation or from Hobby Lobby. A friend of mine picked one up for me, and I set it up on my EFlite 370 outrunner motor. The performance of the unit was marginal, but acceptable. The parts fit was not at all impressive, and I found the unit to be on the cheap side (all plastic). I had a few parts come off in the air, and so far, i wasnt liking the unit. I decided that the hud and grips were a write off, so i put the blades on my TRex tail rotor setup. This worked great, and we had lots of fun messing with the inverted hovers infront of the house. Today, i went and got some stailess steel tubing to use as a shaft in my Axi motor. I swapped out the EFlite to the Axi, and proceded to set up the unit. On the first run up, one of the blades ejected, and shot across the garage. If this had come off and come towards me, i would be very cut up, or even blind.

This thread is a warning if you have one of these or want to set one up. be very aware that this is a problem. i had issues with the pitch slider, hub nut, and blades (that is the entire unit just about). Needless to say, the plane has suffered damage as well. I will repair it, but will never buy one of the EVP setups again.

BEWARE USERS! Mad

_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
thefasttrack



Joined: 09 Apr 2005
Posts: 80
Location: miami

PostPosted: Fri Jul 15, 2005 6:17 pm    Post subject:  

lol did it really shoot across the garage i have to witness somthing like that.
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Fri Jul 15, 2005 8:43 pm    Post subject:  

I honestly figured the setup in general would provide marginal performance. It is very cool looking to have a model fly backwards. I knew you would have to give up something for the VP and that is performance and safety from what has been mentioned.

I like the idea, but I'll pass right now on it.

Thanks for the heads up.
DTB

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1178
Location: Sunnyvale, CA

PostPosted: Fri Jul 15, 2005 11:08 pm    Post subject:  

thefasttrack wrote:
lol did it really shoot across the garage i have to witness somthing like that.


Think of it like this..the blades are spinning at...nearly 18000 rpm (this is at wot and no pitch), and one blade comes off...do you THINK itll just stop and fall? Believe me...it SHOT.

_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
Xipp



Joined: 27 Apr 2005
Posts: 10
Location: Baks.Cali

PostPosted: Mon Jul 18, 2005 9:44 am    Post subject: Zak u toad  

Dude do what i do when setting up one of these things wear clear safty glasses.And if your VPP is working marginal then i suggest that you take the time to trim it out better servo placement for the VPP is critical.The first one i set up was all wrong and when mark earl came over he showed me how to set these things up right..Bring one to camarillo with you and i will bring a tensor with a vpp on it and let you fly it.Another thing if you do not have the newest hi discharge cells from thunder power then it will suffer for power we use a 3 cell 730 gold label.And last but not least get rid of the JST connectors they cannot pass the current needed for good power...see ya in Camarillo...Late
Back to top  
thefasttrack



Joined: 09 Apr 2005
Posts: 80
Location: miami

PostPosted: Mon Jul 18, 2005 1:23 pm    Post subject:  

3dbatixkid wrote:
thefasttrack wrote:
lol did it really shoot across the garage i have to witness somthing like that.


Think of it like this..the blades are spinning at...nearly 18000 rpm (this is at wot and no pitch), and one blade comes off...do you THINK itll just stop and fall? Believe me...it SHOT.

thts crazy
Back to top  
3D-kid330



Joined: 14 Nov 2004
Posts: 391
Location: Fremont, CA

PostPosted: Tue Jul 19, 2005 3:46 pm    Post subject:  

Why on earth did you have that thing at 18000 anyway? No wonder it exploded. eek
_________________
Lower??!!
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Thu Jul 21, 2005 2:01 am    Post subject:  

3D-kid330 wrote:
Why on earth did you have that thing at 18000 anyway? No wonder it exploded. eek
it was running 18,000 because the prop flew off when he had no pitch at the time.
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
3D-kid330



Joined: 14 Nov 2004
Posts: 391
Location: Fremont, CA

PostPosted: Thu Jul 21, 2005 10:23 am    Post subject:  

True, But still, if it was programmed correctly, in center stick with no pitch the throttle should reduce by way of a throttle curve. I've seen a nitro throw one a while ago doing 18 and it was NOT pretty. If you have it at full and a "flat" (no pitch) prop, what do you expect it to do? eek Correct me if I'm wrong, but when you set one up, you are supposed to have 0 pitch at center stick and about half power (so you don't overspeed the blades) and at full stick, you have full pitch and full power, and at low stick you have full power and full pitch. Everything in between is adjusted via throttle and pitch curves. I would not want to be around plastic that is spinning at 18 grand.

Brandon

_________________
Lower??!!
Back to top  
fly boy 1



Joined: 12 Nov 2004
Posts: 286
Location: Milwaukee,WI

PostPosted: Fri Jul 22, 2005 7:33 am    Post subject:  

3D-kid330 wrote:
True, But still, if it was programmed correctly, in center stick with no pitch the throttle should reduce by way of a throttle curve. I've seen a nitro throw one a while ago doing 18 and it was NOT pretty. If you have it at full and a "flat" (no pitch) prop, what do you expect it to do? eek Correct me if I'm wrong, but when you set one up, you are supposed to have 0 pitch at center stick and about half power (so you don't overspeed the blades) and at full stick, you have full pitch and full power, and at low stick you have full power and full pitch. Everything in between is adjusted via throttle and pitch curves. I would not want to be around plastic that is spinning at 18 grand.

Brandon

Yeah, use a futaba GV-1 on it lol
Back to top  
Colin



Joined: 08 Jun 2004
Posts: 25
Location: Canada

PostPosted: Sat Jul 23, 2005 8:40 am    Post subject:  

The more and more you guys fly planes the more you wanna fly helis wink First ya started off hovering and torqin, now ya want your props to change pitch! Get a heli and be done with it Most of em work unibrow

Just playin'

Quote:
Yeah, use a futaba GV-1 on it lol


Seriously though, you can get some SUPER small governors and rpm limiters now a days. But then you're even more like a heli wink

Zak you should know how to setup a throttle curve wink (100 75 50 75 100) hehe, don't you guys have a gas x-smell? smile

Colin

_________________
Great Hobbies
Thunder Tiger
Morgan Fuels
HobbyCraft Canada
Back to top  
 
   3DBatix Forum Index -> Gear Talk All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive