ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

TOC YAK Complete
18 posts
 
   3DBatix Forum Index -> Giant Scale
 
Author Message
Montgomery



Joined: 07 Dec 2004
Posts: 58
Location: Tampa, Florida

PostPosted: Mon Sep 26, 2005 8:49 am    Post subject: TOC YAK Complete  

Hello Everyone,
I've been watching & learning in the backround for a few months and decided to try my hand a building a gasser. I decided to go with the TOC Avaition 30% YAK 54. Set-up is as follows.
Futaba 9CAPS Radio.
5 - JR 8611A's
2 - Fut3050's
1 - Smart-fly power expander
3 - 2800Mah LiIon battery
1 - 2800Mah LiIon, 11.1 volt battery
3 - MPI H/D regulator switches
1 - MPI H/D standard switch
1 - Sullivan Electronic smoke pump.
1 - ZDZ80cc W/ pitts muff / Carbon prop & spinner
and on and on and on.
Maiden flight was this past Saturday and was flawless. Very happy with the way this plane built & fly's. Although the covering leaves somthing to be desired.
I'll attempt to post a few pic's, hope this works!
Back to top  
Montgomery



Joined: 07 Dec 2004
Posts: 58
Location: Tampa, Florida

PostPosted: Mon Sep 26, 2005 8:56 am    Post subject:  

Well, There goes STRIKE ONE. Can someone explain how to post pic's.
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Mon Sep 26, 2005 9:14 am    Post subject:  

Montgomery wrote:
Well, There goes STRIKE ONE. Can someone explain how to post pic's.


While adding a post, on that post page, scroll down to the bottom and under "Add an Attachment" select the location on your photo on you computer. The photo needs to be 640x480 or something like that. It can't be too large or it won't accept the image. Once you add the image, it will post the image when you submit the post.

BTW, can't wait to see your plane. I have a buddy that has a 40% Yak with a DA-150. Sweet flying plane also.



Dippin__it_.jpg
 Description:
 Filesize:  40.24 KB
 Viewed:  623 Time(s)

Dippin__it_.jpg



Yak_in_crowley.jpg
 Description:
 Filesize:  41.92 KB
 Viewed:  623 Time(s)

Yak_in_crowley.jpg



_________________
Fly it hard and hover it low...

My RC Photo Page


Last edited by DTB on Mon Sep 26, 2005 9:47 am; edited 1 time in total
Back to top  
john wondra



Joined: 05 May 2004
Posts: 360
Location: auburn, wa

PostPosted: Mon Sep 26, 2005 9:47 am    Post subject: Re: TOC YAK Complete  

Holly crap dude a ZDZ 80!?! the plane should be 16 lbs! with a ZDZ 80 it will probably hit 19. go with a DA 50 on a pipe or somthing. ZDZ 80 is way to much. All you need is 1 8611 per control surface....
5 8611's and a standard throttle servo... 4 batteries in a 30% is way over kill not to mention excesive weight. you only need 1 4400 for 1 RX. The power expander IMO is useless on a 30%. a few things to think about...
Montgomery wrote:
Hello Everyone,
I've been watching & learning in the backround for a few months and decided to try my hand a building a gasser. I decided to go with the TOC Avaition 30% YAK 54. Set-up is as follows.
Futaba 9CAPS Radio.
5 - JR 8611A's
2 - Fut3050's
1 - Smart-fly power expander
3 - 2800Mah LiIon battery
1 - 2800Mah LiIon, 11.1 volt battery
3 - MPI H/D regulator switches
1 - MPI H/D standard switch
1 - Sullivan Electronic smoke pump.
1 - ZDZ80cc W/ pitts muff / Carbon prop & spinner
and on and on and on.
Maiden flight was this past Saturday and was flawless. Very happy with the way this plane built & fly's. Although the covering leaves somthing to be desired.
I'll attempt to post a few pic's, hope this works!

_________________
John Wondra RAMS VP
Team 3D Foamy/3D Foamy Suport
__________________________
www.3dfoamy.com
www.northwest3d.com
www.e-flightline.com
www.Falconbatteries.com
www.cutimages.com <all your custom vinyl needs>
Back to top  
Montgomery



Joined: 07 Dec 2004
Posts: 58
Location: Tampa, Florida

PostPosted: Mon Sep 26, 2005 10:25 am    Post subject:  

Here comes STRIKE 2


under the hood2.jpg
 Description:
 Filesize:  35.13 KB
 Viewed:  620 Time(s)

under the hood2.jpg



electronics2.jpg
 Description:
 Filesize:  44.62 KB
 Viewed:  620 Time(s)

electronics2.jpg


Back to top  
Montgomery



Joined: 07 Dec 2004
Posts: 58
Location: Tampa, Florida

PostPosted: Mon Sep 26, 2005 10:44 am    Post subject:  

Yea, your right on the weight, Its right @ 18 3/4lbs. I'll play with the smoke for another week or two then the Smoke tank, pump & 11.1 volt 3 cell pack will be removed.
You think I should remove the expander Too. Hmmmm. That would get to around 17lbs or so. The ZDZ 80 is not as heavy as you may think. Although it is heavyer than the DA50 @ 3 lbs, it is still .16 Lbs lighter than the 3W50. You know what they say about a fool and his money. I had surplus left over so just started craming stuff into this thing.
Back to top  
Montgomery



Joined: 07 Dec 2004
Posts: 58
Location: Tampa, Florida

PostPosted: Mon Sep 26, 2005 10:57 am    Post subject:  

1st. motor


canopy.jpg
 Description:
 Filesize:  18.43 KB
 Viewed:  615 Time(s)

canopy.jpg



Carb guide.jpg
 Description:
I did start with the DA.. but wanted more power.
 Filesize:  26.89 KB
 Viewed:  615 Time(s)

Carb guide.jpg


Back to top  
Montgomery



Joined: 07 Dec 2004
Posts: 58
Location: Tampa, Florida

PostPosted: Mon Sep 26, 2005 11:06 am    Post subject:  

ZDZ 80-RV


zdz1.gif
 Description:
 Filesize:  93.28 KB
 Viewed:  613 Time(s)

zdz1.gif


Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Mon Sep 26, 2005 3:19 pm    Post subject:  

you may wanna rethink your ignition cutoff position. a good rule of thumb is to have all of your ignition components(including battery and switch) at least 10 inches away from your reciever components. RF can pass through your ignition components and get into your reciever if theyre too close.
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
Montgomery



Joined: 07 Dec 2004
Posts: 58
Location: Tampa, Florida

PostPosted: Tue Sep 27, 2005 2:26 am    Post subject:  

Thanks John, I removed all components last night & will be reinstalling without smoke system components & power expander. Will be a completely new lay-out with lots more room. Do I understand you correctly that all parts for Ignition must be separated from flight control parts? If so I guess the choak servo which is right next to the Ignition is not a very good idea. Any advice on new lay-out? Like I said, I,m still learning about gas and imput is very much appreciated.
Also, I do have JR snap around RF flters. Are these of any use for me?
Back to top  
Robert300L



Joined: 17 Apr 2004
Posts: 134
Location: San Diego, CA

PostPosted: Tue Oct 04, 2005 12:03 pm    Post subject:  

Butthead wrote:
you may wanna rethink your ignition cutoff position. a good rule of thumb is to have all of your ignition components(including battery and switch) at least 10 inches away from your reciever components. RF can pass through your ignition components and get into your reciever if theyre too close.


What have you been smoking?

I'd be more worried about the throttle and choke servos than the cutoff stick out tongue
Realistically though, if your ignition is working properly*cough*not a CH ignition*cough* then you can probably wrap your battery wires around the module and still be able to fly. I would concider putting the choke and throttle servos farther back, but it wouldn't hurt to range check it there and see what it does. I had my batteries 3" from my ignition module on my ZDZ and had no problems. Everything else actually looks fine there to me. However, since it's been a week, I assume you've played with it a bit since then.
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Tue Oct 04, 2005 2:58 pm    Post subject:  

Robert300L wrote:
Butthead wrote:
you may wanna rethink your ignition cutoff position. a good rule of thumb is to have all of your ignition components(including battery and switch) at least 10 inches away from your reciever components. RF can pass through your ignition components and get into your reciever if theyre too close.


What have you been smoking?

I'd be more worried about the throttle and choke servos than the cutoff stick out tongue
Realistically though, if your ignition is working properly*cough*not a CH ignition*cough* then you can probably wrap your battery wires around the module and still be able to fly. I would concider putting the choke and throttle servos farther back, but it wouldn't hurt to range check it there and see what it does. I had my batteries 3" from my ignition module on my ZDZ and had no problems. Everything else actually looks fine there to me. However, since it's been a week, I assume you've played with it a bit since then.

me? i haven't been smokin nuthin LOL, i know he doesnt have to, its just good practice. i've had interference from my ignition module before. i was running FM though. with PCM its no problem.

_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
Montgomery



Joined: 07 Dec 2004
Posts: 58
Location: Tampa, Florida

PostPosted: Wed Oct 05, 2005 3:11 am    Post subject:  

Ok, Took some much appreciated advice from you experts. Here is what I came up with. Removed all the frills & choak servo. (installed manual choak via bell crank) She comes in @ 17.2lbs with the ZDZ80.


Layout 2.jpg
 Description:
 Filesize:  12.68 KB
 Viewed:  424 Time(s)

Layout 2.jpg


Back to top  
Montgomery



Joined: 07 Dec 2004
Posts: 58
Location: Tampa, Florida

PostPosted: Wed Oct 05, 2005 3:15 am    Post subject:  

Dont know why that picture came out so small. Cant seem to get anything right the 1st. time


Indoor hangar.jpg
 Description:
 Filesize:  40.36 KB
 Viewed:  422 Time(s)

Indoor hangar.jpg



Ballanceing Act.jpg
 Description:
 Filesize:  22.4 KB
 Viewed:  422 Time(s)

Ballanceing Act.jpg


Back to top  
Montgomery



Joined: 07 Dec 2004
Posts: 58
Location: Tampa, Florida

PostPosted: Wed Oct 05, 2005 3:24 am    Post subject:  

Trying again.


Layout 2.jpg
 Description:
 Filesize:  41.43 KB
 Viewed:  420 Time(s)

Layout 2.jpg


Back to top  
xtraflyr



Joined: 10 Sep 2005
Posts: 28
Location: Chester NJ

PostPosted: Fri Oct 07, 2005 6:21 pm    Post subject:  

hey montgomery,

What do you really think about this Yak? Since EF looks like it's never coming in,I'm thinking about this one.. Confused

Later

_________________
REAL PLANES HAVE A ROUND COWL AND a MONOWING!!!

1/3 Lanier Laser200,Brison 4.2 JR 8103, Hitecs

QQ YAK OS160 JR 8103, Hitecs

Midwest Cap 80" DA50 JR 8103,Hitecs

Funtana 90s YS 120sf, JR 9303 PCM,Hitecs
Back to top  
Robert300L



Joined: 17 Apr 2004
Posts: 134
Location: San Diego, CA

PostPosted: Fri Oct 07, 2005 7:11 pm    Post subject:  

Looks good!

Purple walls? Shocked
Back to top  
Montgomery



Joined: 07 Dec 2004
Posts: 58
Location: Tampa, Florida

PostPosted: Mon Oct 10, 2005 4:48 am    Post subject:  

Xtraflyr, I love this plane. After I removed a bout 1 1/2lbs of stuff I did'nt realy need it flys very light. Knife edge is like it is on rails, hovering is very stable, IMAC sequences are clean & deliberate. I have found no bad tendencies at all. The build is easy & everything lines up perfectly, Unlike the some of the EF Yaks.
I also think the ZDZ80cc is a great combo with this plane. The extra power is nice when in a pinch. Its a little heavyer than the DA50 but still lighter than the 3W50.
I had one of the more accomplished 3D pilots take her up yesterday & put it to the test. He, and everyone watching was amazed at the 3D capability of this plane. I dont think you can go wrong with this plane so go for it.
As for the PURPLE walls.... This was my daughters room, she joined the Air Force last year, so I moved from the gurauge into her room & have not gotton around to painting. This is a much cooler place to work in the Florida Summer!
Back to top  
 
   3DBatix Forum Index -> Giant Scale All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive