ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Powerline Edge 540 Build thread
15 of 59 posts archived
 
   3DBatix Forum Index -> Workshop
 
Author Message
mikey



Joined: 28 Nov 2004
Posts: 109
Location: Greenville, TX

PostPosted: Mon Oct 24, 2005 11:54 am    Post subject: Powerline Edge 540 Build thread  

I ordered it thursday night and it showed up today monday. That is very fast much faster than anything else I ever ordered. The kit quality is as good as the hanger 9 stuff. The covering job is great way above par. Only a few wrinkles but to be expected coming from over seas. That is a easy fix. If they did not have the few problems that I found so far I would put them up there with extreme flight. Problems so far with the kit is two ca hinges were pushed all the way into the ailron not sure how to get it out might just have to leave them. The other is the elevator joiner rod is not a percise cut out to the elavator halves will have to mod it to make it fit square. The yellow and black looks much better in person than the photo. Was not to much on getting the yellow and black but once I saw the plane live I am very happy with it.


Picture 003.jpg
 Description:
The plane looks better in real life.
 Filesize:  57.02 KB
 Viewed:  1148 Time(s)

Picture 003.jpg



Picture 002.jpg
 Description:
If you look close you can see the ca hinges pushed all the way in.
 Filesize:  43.32 KB
 Viewed:  1148 Time(s)

Picture 002.jpg



Picture 001.jpg
 Description:
The is the elvator halves as you can see they were not cut correctly.
 Filesize:  44.13 KB
 Viewed:  1148 Time(s)

Picture 001.jpg


Back to top  
Radioflyer



Joined: 14 Sep 2004
Posts: 344
Location: Kalamazoo, MI

PostPosted: Mon Oct 24, 2005 5:16 pm    Post subject:  

Did you order from Jag? I talked to them and they seemed to be very nice, they were just waiting for the other colors to come in. Is that a fiberglass cowl and pants? Looks SWEET
_________________
God bless us all, and keep us safe.


www.bryanhusk.com/jay
Back to top  
mikey



Joined: 28 Nov 2004
Posts: 109
Location: Greenville, TX

PostPosted: Mon Oct 24, 2005 8:01 pm    Post subject:  

Yes I ordered it from jag and yes the cowl and pants are fiber glass. They clear coated over the stickers on the cowl which means they won't peal off this is a good thing. I would like to take back my first impression statement that the quality was as good as hanger 9. The kit quality overall is just not as good as hanger 9. The direction can't be called directions they need a lot of help they expect you to know alot. This kit would be unduable for a beginer. But the covering is bar none one of the best jobs that I have seen I hate to say this but after close inspection they have extreme flight beat. I pulled all the wrinkles out it looks great. I managed to get the ca hinges out of the ailron that were pushed in. All control surface were servely worped I was able to straighten them with a large heat iron. Not sure what kind of covering it is I have never then this type before it is like a cloth on the inside very strong. It is low temp when you tighten the mono coat don't go above 180 degrees celisus on the iron trust me the top monocoat will melt and DON'T USE A HEAT GUN trust me on that one two. Read the comments on the pictures for explantion.


Picture 012.jpg
 Description:
I decided to go with there ca hinges did not want to spend to much time on a 40 size airplane. I wish that all manufactures would start going with robart style hinges and have them predrilled and hinged.
 Filesize:  39.38 KB
 Viewed:  1127 Time(s)

Picture 012.jpg



Picture 010.jpg
 Description:
These are made very well a little on the heavy side but they feel very stong. Much stonger than the funtana. The paint job is not as good as hanger 9. They use phillips head set screw on the wheel coaler instead of a allen makes it hard to set and not
 Filesize:  37.26 KB
 Viewed:  1127 Time(s)

Picture 010.jpg



Picture 008.jpg
 Description:
If you see the axles they were different sizes on had to be cut to fit another quality control isssue.
 Filesize:  30.56 KB
 Viewed:  1127 Time(s)

Picture 008.jpg



Picture 007.jpg
 Description:
I used a large iron a 180 degrees celisusto straighten and get the wrinkles out. Would not go any higher than that this stuff is low temp. The quality of the monocoat is bar none great.
 Filesize:  56.1 KB
 Viewed:  1127 Time(s)

Picture 007.jpg



Picture 005.jpg
 Description:
If you look you wiil see the gap that the rib in the ailron does not fit. Just an example of how quality is just not quite there.
 Filesize:  33.62 KB
 Viewed:  1127 Time(s)

Picture 005.jpg




Last edited by mikey on Wed Oct 26, 2005 7:13 pm; edited 1 time in total
Back to top  
mikey



Joined: 28 Nov 2004
Posts: 109
Location: Greenville, TX

PostPosted: Mon Oct 24, 2005 8:10 pm    Post subject:  

Here are some more pics.


Picture 014.jpg
 Description:
This is one of those what were they thinking. The servo horn was right behind the servo. And the horn was not set over the center of the hinger line. I moved it over as far as I could get it while still having the screws going into the reinforceing blo
 Filesize:  40.3 KB
 Viewed:  1126 Time(s)

Picture 014.jpg



Picture 013.jpg
 Description:
I used thin ca on all the holes that the servo mount screws go into.
 Filesize:  43.69 KB
 Viewed:  1126 Time(s)

Picture 013.jpg



Picture 017.jpg
 Description:
I pushed the surfaces together and raised it till I had 45 degrees and this is the gap that I ended up with. They need a better beval.
 Filesize:  31.47 KB
 Viewed:  1126 Time(s)

Picture 017.jpg


Back to top  
mikey



Joined: 28 Nov 2004
Posts: 109
Location: Greenville, TX

PostPosted: Tue Oct 25, 2005 6:16 pm    Post subject:  

I finshed up the ailorons I think I got them the way that I want them. Everything lines up fairly nice I got the horn over the hing line were it goes. The horn is a little to the side because the reinforcing block does extend far enough over so I have it as far over as it will go.


Picture 019.jpg
 Description:
I have the horn centered over the hinge line.
 Filesize:  46.33 KB
 Viewed:  1095 Time(s)

Picture 019.jpg



Picture 018.jpg
 Description:
The horn is over as far as it will while still being in the renforcing block.
 Filesize:  37.7 KB
 Viewed:  1095 Time(s)

Picture 018.jpg


Back to top  
mikey



Joined: 28 Nov 2004
Posts: 109
Location: Greenville, TX

PostPosted: Tue Oct 25, 2005 6:20 pm    Post subject:  

They have strings attached to blocks of wood to pull the servo lead through the wing. They are lightly glued just pull and they break off.


Picture 020.jpg
 Description:
 Filesize:  30.06 KB
 Viewed:  1094 Time(s)

Picture 020.jpg


Back to top  
mikey



Joined: 28 Nov 2004
Posts: 109
Location: Greenville, TX

PostPosted: Tue Oct 25, 2005 7:04 pm    Post subject:  

Ok I got the engine mount figured out. There is no way to make the horizontal thrust lines to line up with the motor mount. You have to push the mount as far up as you can get it to the top. The way the mount is so poorly designed it will not line up so I got it as close as I could get it. There is a line on the mount to line up the vertical thrust line. By the way the instruction do not mention any of this they act like the mount holes are already installed.


Joey 002.jpg
 Description:
Put the mount all the way to the top
 Filesize:  57.66 KB
 Viewed:  927 Time(s)

Joey 002.jpg




Last edited by mikey on Thu Nov 03, 2005 10:22 pm; edited 4 times in total
Back to top  
Radioflyer



Joined: 14 Sep 2004
Posts: 344
Location: Kalamazoo, MI

PostPosted: Wed Oct 26, 2005 11:54 am    Post subject:  

Looks good. It sounds like you want to have built quite a few models before tackling this one. Good build thread, it will certainly take the guess work out for future Edge owners big grin
_________________
God bless us all, and keep us safe.


www.bryanhusk.com/jay
Back to top  
Shaun



Joined: 10 Sep 2004
Posts: 342
Location: texas

PostPosted: Wed Oct 26, 2005 2:02 pm    Post subject:  

Well it looks good! Don't know what else to say abou tthe rest of the kit? The miss cut elevators would really hack me off. And the missed placed aileron control horn block would have also raised my brow a tad.
I've delt with bad directions before. I guess I'll hold judgement until I see the video smile.
Great write up!!

_________________
http://www.texomarc.org/
Back to top  
cyoung450



Joined: 03 Nov 2005
Posts: 1

PostPosted: Thu Nov 03, 2005 7:40 pm    Post subject: Powerline EDGE  

Great looking plane I love mine. Make sure you beef up the landing gear, and put tail braces on it, I used carbon fiber rods for mine and they work well. You will love this plane. This picture is from the first day I put the braces on a few days later.


EDGE540_1stDay_01_small.JPG
 Description:
 Filesize:  49.46 KB
 Viewed:  930 Time(s)

EDGE540_1stDay_01_small.JPG


Back to top  
fly boy 1



Joined: 12 Nov 2004
Posts: 286
Location: Milwaukee,WI

PostPosted: Thu Nov 03, 2005 7:54 pm    Post subject:  

That looks awesome. I think i'm going to get one for my evo 46. I think it should fly it ok, prolly a little weak on power tho, but i'll see.
_________________
Team Greenfield News and Hobby

Dave Partick 27% Extra 330L
Raptor 50
TOC1 30% Yak 54
Judge 540
Shocky Extra

http://www.greenfieldnewsandhobby.com
Back to top  
mikey



Joined: 28 Nov 2004
Posts: 109
Location: Greenville, TX

PostPosted: Thu Nov 03, 2005 9:11 pm    Post subject:  

I got the horizontal and elevator installed. The directions tell you to install them in halves like it is a split elevator but the elevator comes with a joiner with it and the elevator is pre cut for the joiner and the plane only has one servo mount for the elevator. So I assumed that it should be joined. I glued the elevator half’s together off the plane to make sure that I got them straight. So what I did was cut a slot in the back of the slot for the horizontal to move it back so I could get the hinges in.


Joey 012.jpg
 Description:
 Filesize:  44.38 KB
 Viewed:  917 Time(s)

Joey 012.jpg


Back to top  
mikey



Joined: 28 Nov 2004
Posts: 109
Location: Greenville, TX

PostPosted: Thu Nov 03, 2005 9:47 pm    Post subject:  

So all the horns on the plane were in the wrong location the elevator was close but set at the wrong angle. The rudder horn if instaled in the location the they predrilled would not allow the elevator to move down at all. Note this was the horn they sent me and the holes they drilled. the instruction call for a pull pull rudder. They did not send any hardware for a pull pull and there was no servo tray installed in the plane for a pull pull. They cut a servo tray in the back for rudder servo. So with the harware they did send me I assume that they want you to use a standered steup. These instruction are not only very incomplete they are just flat wrong I have never seen any thing like this before.


Joey 008.jpg
 Description:
You have to put the rudder horn low to clear the elevator.
 Filesize:  47.53 KB
 Viewed:  915 Time(s)

Joey 008.jpg


Back to top  
mikey



Joined: 28 Nov 2004
Posts: 109
Location: Greenville, TX

PostPosted: Thu Nov 03, 2005 9:54 pm    Post subject:  

The servo tray should be higher so that you could get the linkage to line up correctly. They should have assumed that everyone would use a one to one setup.


Joey 006.jpg
 Description:
 Filesize:  56.75 KB
 Viewed:  913 Time(s)

Joey 006.jpg


Back to top  
mikey



Joined: 28 Nov 2004
Posts: 109
Location: Greenville, TX

PostPosted: Thu Nov 03, 2005 9:57 pm    Post subject:  

I really wanted to get the tank on the cg so what I did was got two 6oz tanks so that they would fit under the wing tube.


Joey 013.jpg
 Description:
 Filesize:  43.29 KB
 Viewed:  912 Time(s)

Joey 013.jpg


Back to top  
44 posts after this were not archived
 
   3DBatix Forum Index -> Workshop All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive