ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

What Servos?
8 posts
 
   3DBatix Forum Index -> 3D Talk
 
Author Message
dizzane



Joined: 08 Dec 2005
Posts: 4

PostPosted: Thu Dec 08, 2005 6:09 am    Post subject: What Servos?  

I have been flying about four years now and I am now gettiing ready to build my first 50cc sized plane. I have lots of ?s cause this will also be my first gas plane, I just ordered my DA50 and it should be her somtime next week. Ok now to my servos question: is there any way to figure out what torque I will need for my new plane? I am building the new Aero-Works Yak 54, it will not be here tell Jan. but I want to get everything to gether.
Thanks for all your help,
Duane
Back to top  
Montgomery



Joined: 07 Dec 2004
Posts: 58
Location: Tampa, Florida

PostPosted: Thu Dec 08, 2005 10:01 am    Post subject:  

You can never go wrong with the JR8611A's IMO. It may be a little overkill for a 50cc plane @ 320oz of torque, But you will always have them to use if you get into the 33% to 40% range. I have a total of 22 all together and never had any trouble with any of them.
Here comes the Hitek guys. UT
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1178
Location: Sunnyvale, CA

PostPosted: Thu Dec 08, 2005 12:33 pm    Post subject:  

I think for a 50cc gasser you might as well get the high tork servos that would work in a 40%. Like Mongomery said the 8611s are good servos. I personally have had a brand new one fail but that may just be a fluke. The Futaba 9351s are awersome as well. As far as Hitecs, the new 5995s have pretty amazing specs, but im a little leery about the software.

In general, i think you should shoot for about 150oz/in. of tork or more for this plane.

Hope this helps Surprised

_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
fly boy 1



Joined: 12 Nov 2004
Posts: 286
Location: Milwaukee,WI

PostPosted: Thu Dec 08, 2005 3:06 pm    Post subject:  

I use hitec 5645's on my toc1 yak 54. No blowback at full throttle. I do use an 8611a for the rudder tho. The hit'ecs are fine on ailerons and elevators. You could also get the hitec 5945's, or the futaba 9351's. I went the cheap route, no problems tho. I can see using 5955's, but I don't want to spend that much on servo's for a plane that will eventually become the beater plane.
_________________
Team Greenfield News and Hobby

Dave Partick 27% Extra 330L
Raptor 50
TOC1 30% Yak 54
Judge 540
Shocky Extra

http://www.greenfieldnewsandhobby.com
Back to top  
Swat Cop



Joined: 10 Jun 2004
Posts: 48
Location: Kissimmee, FL

PostPosted: Thu Dec 08, 2005 3:09 pm    Post subject: Servos  

You are going to get a lot of opinions on servos and it really comes down to what you want to spend. If you plan on someday getting a 40% plane maybe you will want to go all out. It also depends on your flying style. If you are doing hardcore 3D, IMAC or just sport flying. For a 50cc plane I would recommend Hitec 645MG or 625MG if you don't want to go the digital route if you want digitals I would go with 5645MG. You can see what I fly here and all have Hitec digitals except the biplane. I have never had a Hitec servo fail either. Very Happy

http://hometown.aol.com/bike466/index.html

_________________
http://hometown.aol.com/bike466/index.html

Sunset Flyers St. Cloud, FL
Skyhigh Flyers Orlando, FL
Back to top  
Shaun



Joined: 10 Sep 2004
Posts: 342
Location: texas

PostPosted: Thu Dec 08, 2005 4:46 pm    Post subject:  

Quote:
You are going to get a lot of opinions on servos

Swats right. I have had Hitec 645 on both my Funtana90 and my Dave Patrick 120 size Ultimate. I now have JR 8611's all the way around on my 28% Wild Hare extra. Both did very well.The 8611's might be overkill right now but it's better to go that direction then to week! Confused
Shaun

_________________
http://www.texomarc.org/
Back to top  
dizzane



Joined: 08 Dec 2005
Posts: 4

PostPosted: Thu Dec 08, 2005 4:48 pm    Post subject:  

Thanks for all the info guys I think I am going to use the Hitec 5945s I have the 5625s right now but I will pick up some 5945s.
Back to top  
Swat Cop



Joined: 10 Jun 2004
Posts: 48
Location: Kissimmee, FL

PostPosted: Fri Dec 09, 2005 5:47 pm    Post subject: Servos  

Great choice. I have 5945s on my 40% Cap and 2.6m Composite Edge 540. I really like the fact that they are programmable. You can't go wrong with JR's either just a little more $$ than the Hitecs and not programmable.
_________________
http://hometown.aol.com/bike466/index.html

Sunset Flyers St. Cloud, FL
Skyhigh Flyers Orlando, FL
Back to top  
 
   3DBatix Forum Index -> 3D Talk All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive