ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

50cc Yak Radio Setup
5 posts
 
   3DBatix Forum Index -> Giant Scale
 
Author Message
dizzane



Joined: 08 Dec 2005
Posts: 4

PostPosted: Tue Dec 13, 2005 9:11 pm    Post subject: 50cc Yak Radio Setup  

Ok I am getting ready to build my first 50cc plane, AreoWork Yak(not here yet). But I was just wanting to know what you guy would suggest for a radio set, I have all me servos and RX, I am just want to know what to set up as far as batteries... back up systems... do I do dual RX? Can you guys suggest a good setup for this size of a plane. I am new to these larger planes and I just do not want to lose this plane to a bad setup. Thanks for all the help guys,
Duane[/b]
Back to top  
Tampa Bay Flyer



Joined: 09 Dec 2005
Posts: 22
Location: Tampa, Florida

PostPosted: Wed Dec 14, 2005 9:29 am    Post subject:  

Here is the set up on my TOC YAK.
3 - 2800 Mah Li-Ion battery packs.
3 - Heavy duty switches with regulators
1 - Smart Fly ignition cut off
1 - Futaba 9channel receiver.
If you are going to have a failure somewhere, it will probably be in the battery packs or the switches. I Always use redundant packs on all my planes. Receiver failure does sometimes happen but is very rare. I also think you may have a little trouble finding room for the redundant receiver's as they need to be 25cm to 30cm minimum apart from each other. The Smart Fly cut off is a must. Adds Safety & helps eliminate RF.
You could go all out and install a power expander, Smoke System, etc. but remember..Light planes fly better, and you don't really need it on a 50cc plane.
Congrats on your plane & good luck with the build. Applause



YAK Radio.jpg
 Description:
 Filesize:  54.5 KB
 Viewed:  153 Time(s)

YAK Radio.jpg



_________________
Monty,

QQ 72" Yak
TOC 30% YAK
Comp Arf 40% SuperX
Back to top  
dizzane



Joined: 08 Dec 2005
Posts: 4

PostPosted: Wed Dec 14, 2005 9:55 am    Post subject:  

Thanks for the info, that will help, what brand of batteries are you using?
Back to top  
3D-kid330



Joined: 14 Nov 2004
Posts: 391
Location: Fremont, CA

PostPosted: Wed Dec 14, 2005 4:13 pm    Post subject:  

Those look like the TBM Li-ions. I think you can find them at www.Troybuiltmodels.com .

Any kind of li-ion will work, like Duralite, TBM, Fromecco (SP?)

I run a Duralite 2800 in my Edge, it runs all the servos and the smoke pump. It has two packs in it though, to total 4 cells. So if one pack drops out, it switches to the other pack. That way you can have better redundancy, less weight, and simplicity rather than having two packs seperate. Thats the best I can describe it with a miserable cold...lol
Maybe someone can describe it better.

You can even use a 2 cell li-poly provided you use a regulator, but I think for giant scale the Li-ion is better. Just IMHO.

_________________
Lower??!!
Back to top  
fly boy 1



Joined: 12 Nov 2004
Posts: 286
Location: Milwaukee,WI

PostPosted: Wed Dec 14, 2005 7:31 pm    Post subject:  

Well, dual battery set up's are kinda dumb in this size imo. I know it's all about redundancy and all, but that is a little extreme for this small of a plane. It is just too much money, and weight. My set up in my toc yak is old school i guess, I just runa a bigg ass 3300 mah nimh 6 volt on a reg, and that lasts for ever, and was only $40. If I had the money that some people do , I can see goin all out, but I wanted to keep it on the cheap side. I am running hitec 5645 servo's as well, with an 8611a on the rudder. I am also running a futaba 319 reciever, which I run in almost all of my planes. Have fun with your yak, it'll 3d like you won't believe.
Eric

_________________
Team Greenfield News and Hobby

Dave Partick 27% Extra 330L
Raptor 50
TOC1 30% Yak 54
Judge 540
Shocky Extra

http://www.greenfieldnewsandhobby.com
Back to top  
 
   3DBatix Forum Index -> Giant Scale All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive