ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

mini extra 330...
15 of 24 posts archived
 
   3DBatix Forum Index -> Foamies
 
Author Message
selfoDESIGN



Joined: 17 Dec 2005
Posts: 12
Location: kansas city

PostPosted: Sat Dec 17, 2005 9:00 pm    Post subject: mini extra 330...  

well after a ten year break from RC Im back and the first thing I did was rape the 3dbatix site of all plans....

first on the list was a scaled down extra as it seems everyone is having so much fun with the larger ones.

My main motivation is smaller is better when you live in the city in an appt.

so has anyone made one smaller??
and how ya think this model will fly this small

specs are as follows:
3mm depron
aleron/elev
span 18 in.
auw: 5.2 oz.
static thrust: 5.0 oz.
graupner speed 280
e-flite servos
gws rec.
tp lipos 2s900mah
castle creations s.c.

and what ..... where are the pics....... eek




_________________
to be truely creative one must first smash accepted values....
Back to top  
dejci23



Joined: 02 Dec 2005
Posts: 5
Location: Slovenia

PostPosted: Sun Dec 18, 2005 7:07 am    Post subject:  

Nice work!

Do you have any movie from this model?
Back to top  
selfoDESIGN



Joined: 17 Dec 2005
Posts: 12
Location: kansas city

PostPosted: Sun Dec 18, 2005 1:23 pm    Post subject:  

not just yet little too much snow on the ground

maiden will be soon though

_________________
to be truely creative one must first smash accepted values....
Back to top  
selfoDESIGN



Joined: 17 Dec 2005
Posts: 12
Location: kansas city

PostPosted: Mon Dec 19, 2005 4:42 pm    Post subject:  

well after completing the model it was a little tail heavy so I made some landing gear.......better than dead weight.

took it to work today to show it off and wouldnt you believe it......
0 wind and the snow was just melted enough to peek my interest.
went to the field and thought "man I dont even have pics of it with the lg.....and boy does it look good right now......

ta hell with that gave it full throttle and tossed it ten feet into the air..
no turning back now...

needless to say it flies like a dream and is very gentle.....
mabye a little too gentle......shoulda went speed 300 instead of 280
anyhow madien was a success and even controlled enough to land it in a grass patch no bigger than the plane.

hum mabye a brushless outrunner......
vids will follow when i can get somebody to stand in the 11 degree weather with me long nuff to get it!

_________________
to be truely creative one must first smash accepted values....
Back to top  
selfoDESIGN



Joined: 17 Dec 2005
Posts: 12
Location: kansas city

PostPosted: Mon Dec 19, 2005 9:15 pm    Post subject:  

couple of new pics.....

lg baby


i.f.f.c ...... you decide!


Shocked

_________________
to be truely creative one must first smash accepted values....
Back to top  
boolat



Joined: 29 Nov 2005
Posts: 19

PostPosted: Tue Dec 20, 2005 2:57 am    Post subject:  

very very beautiful eek

a person who has the plan in pdf?

Dancks
Back to top  
selfoDESIGN



Joined: 17 Dec 2005
Posts: 12
Location: kansas city

PostPosted: Tue Dec 20, 2005 5:43 am    Post subject:  

I just reduced the non-tiled plans to 18 in. wingspan and used 3mm depron. As far at the servo holes and what not i just started with what was on the small plans and made the opening bigger as needed.

Ill see if I can whip some up with the correct sizes and what not

last but not least thanks for the kind words!

friday should be 50 degrees and light wind.....
if all goes well Ill try to get some vid then

_________________
to be truely creative one must first smash accepted values....
Back to top  
boolat



Joined: 29 Nov 2005
Posts: 19

PostPosted: Tue Dec 20, 2005 7:04 am    Post subject:  

why the non-tiled ?

you have print on A4 sheets ?
Back to top  
selfoDESIGN



Joined: 17 Dec 2005
Posts: 12
Location: kansas city

PostPosted: Tue Dec 20, 2005 7:57 am    Post subject:  

the reason for the non-tiled is that i plot my plans on my 48 inch plotter at work
_________________
to be truely creative one must first smash accepted values....
Back to top  
boolat



Joined: 29 Nov 2005
Posts: 19

PostPosted: Tue Dec 20, 2005 8:08 am    Post subject:  

for your opinion if I do not know trace ! Embarassed

what do I have to make to have the same result on A4 sheets for prints ?

if I download this : EXTRA 330 3D Plans - Tiled !

then I reduces all the pages with Acrobat Reader Professional on to 18 in !

And print all on the A4 sheets!

its correct ?

dancks.
Back to top  
selfoDESIGN



Joined: 17 Dec 2005
Posts: 12
Location: kansas city

PostPosted: Tue Dec 20, 2005 8:27 am    Post subject:  

here are the properly scaled drawings


extra330PLOT18inch.zip
 Description:
have fun!

Download (not archived)
 Filename:  extra330PLOT18inch.zip
 Filesize:  176.21 KB
 Downloaded:  74 Time(s)

Back to top  
selfoDESIGN



Joined: 17 Dec 2005
Posts: 12
Location: kansas city

PostPosted: Tue Dec 20, 2005 8:30 am    Post subject:  

use poster printing option!!!
_________________
to be truely creative one must first smash accepted values....
Back to top  
boolat



Joined: 29 Nov 2005
Posts: 19

PostPosted: Tue Dec 20, 2005 8:41 am    Post subject:  

Dancks Razz
Back to top  
selfoDESIGN



Joined: 17 Dec 2005
Posts: 12
Location: kansas city

PostPosted: Tue Dec 20, 2005 9:03 am    Post subject:  

lemme see your progress....and have fun!
_________________
to be truely creative one must first smash accepted values....
Back to top  
boolat



Joined: 29 Nov 2005
Posts: 19

PostPosted: Thu Dec 22, 2005 2:38 pm    Post subject:  

I finished the assembly Mini 330 cool

soon photographs on the forum...

To follow ....

my extrema 330s!

















Then large the crash known centuries! ....

MADMAX BY BOOLAT :





Bye.
Back to top  
9 posts after this were not archived
 
   3DBatix Forum Index -> Foamies All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive