 |
 |
| |
| Author |
Message |
mikeyp
Joined: 01 Jan 2006 Posts: 3 Location: U.K.
|
Posted: Sun Jan 01, 2006 11:24 am Post subject: setup? |
|
|
hi,
ive got the bug and built the extra 330 3d and the foame IIx 3d before i even had any gear to fly with.
i have a futaba 6exa and got the rest off a guy after showing him my extra.
he supplied me with a 2410-12 star motor and 10a esc,10 x 4.7 prop, 11.1v 900ma lipos, 9g tower pro servos, 6 ch reciever charger etc...
the extra flies ok but its very slow in the air, does anyone know if i have the right motor or what can i do to get better performance, a gearbox maybe ??
Thanks,
Mike |
|
| Back to top |
|
 |
3dbatixkid Moderator

Joined: 15 Apr 2004 Posts: 1178 Location: Sunnyvale, CA
|
Posted: Sun Jan 01, 2006 12:48 pm Post subject: |
|
|
I have no idea what kind of motor that is, but it seems like its swinging a pretty small prop for that size of plane. Some options are the AXI 2212/34. I run a 12x6 or 12x8 prop on this motor, but you need a 25amp speed control. The 900mah pack should be enough to fly it, but i use a 1320.
You can also go with the himax 2812-850. This motor would swing an 11x7 or a 12x6. Again, a 25amp controller is needed, and a 1320mah pack is the best.
One setup that ive seen that works with the 10amp controller is the EFlite park 370 1360kv motor. This setup flew well on a 1320 and a 10x4.7. I would imaine (since this motor only needs a 10 amp controller) that you would be able to run the 900s just as well as a 1320.
Hope this helps, _________________ Zak West
www.DesertAircraft.com
www.Smart-Fly.com
www.DarrolCady.com
www.CoolRunningUSA.com
www.TanicPacks.com |
|
| Back to top |
|
 |
mikeyp
Joined: 01 Jan 2006 Posts: 3 Location: U.K.
|
Posted: Mon Jan 02, 2006 6:18 am Post subject: |
|
|
hi,
thanks for the reply, looking at your motor it specs about thsame as mine and also specs a 10" prop too, will it be ok to put a larger prop on my motor?
heres a link with the motor on. http://www.himodel.com/en/rc_hobby/electric_747.php
Or how about i build the extra with 3mm depron instead?
thanks again,
Mike |
|
| Back to top |
|
 |
3dbatixkid Moderator

Joined: 15 Apr 2004 Posts: 1178 Location: Sunnyvale, CA
|
Posted: Mon Jan 02, 2006 11:37 am Post subject: |
|
|
You can try putting a bigger prop on it, but i think that it will not swing it. I dont know if the specs on that motor are very accurate. The bottom line is its a cheap motor. Ive seen similar specs between axi and himax, and the axi has always outperformed. Try a bigger prop, its cheaper than a new motor for now.
You can try building the plane out of 3mm foam. As long as your equipment is light enough, it should be fine. You will have to employ some different building techniques, such as using flat carbon on the LE and TE of the wings instead of a carbon tube spar, and also you will probably have to put carbon support rods from the fuse to the wing. Tail twist will be an issue, but that can be fixed by adding some depron between the vertical and horizontal fuse at a 45 degree angle (like triangle stock).
Hope this helps _________________ Zak West
www.DesertAircraft.com
www.Smart-Fly.com
www.DarrolCady.com
www.CoolRunningUSA.com
www.TanicPacks.com |
|
| Back to top |
|
 |
mikeyp
Joined: 01 Jan 2006 Posts: 3 Location: U.K.
|
Posted: Mon Jan 02, 2006 3:18 pm Post subject: |
|
|
Hmmmm....
im going shopping for a new motor tomorrow, hopefuly the 2212/34 and the 12" prop.
i hacked my extra up today, i removed the undercarriage, trimmed the top and botton of the fuselage and lost all the ends of my horns and had 4 batteries of flying today and it was great fun.... not quite 3d performance but.. : )
i hope to get the new motor in the foameII soon,
Thanks again,
Mike |
|
| Back to top |
|
 |
| |
Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group
blueGray theme by Nuttzy
|