| |
| Author |
Message |
Gezoid

Joined: 24 May 2004 Posts: 161 Location: UK
|
Posted: Thu Jan 12, 2006 4:44 am Post subject: Fliton Freestyle Extra 330? |
|
|
What's everyone think of the Fliton Freestyle Extra 330 for 3D? Just discovered that we can get them in the UK now, at last! I got a 91 four stroke to put in it. It's pretty expensive over here but I love Extra's! How's it compare to, say, Funtana 40?
Thanks for any help. _________________ Ya torkin' ta me? |
|
| Back to top |
|
 |
Batix Kid

Joined: 07 Apr 2005 Posts: 90
|
Posted: Thu Jan 12, 2006 1:51 pm Post subject: |
|
|
| Where and how can you get them in the uk,how much are they? |
|
| Back to top |
|
 |
3dbatixkid Moderator

Joined: 15 Apr 2004 Posts: 1178 Location: Sunnyvale, CA
|
|
| Back to top |
|
 |
Gezoid

Joined: 24 May 2004 Posts: 161 Location: UK
|
Posted: Fri Jan 13, 2006 8:03 am Post subject: |
|
|
Al's Hobbies - £190...
Zak, any idea of the wing area? Apparently it's top secret! It's just not mentioned in the ad's anywhere, so I'm guessing the wing loading is pretty high... Any info anyone? _________________ Ya torkin' ta me? |
|
| Back to top |
|
 |
3dbatixkid Moderator

Joined: 15 Apr 2004 Posts: 1178 Location: Sunnyvale, CA
|
|
| Back to top |
|
 |
qweedqwag
Joined: 11 Jul 2005 Posts: 9
|
Posted: Fri Jan 13, 2006 1:11 pm Post subject: Fliton 330 |
|
|
Zak,
I did finish mine but pancaked it on final, I was really pissed. To everyone make sure that you keep the tank below the engine if you run inverted, otherwise you will have flooding problems like I did, caused a deadstick and fell out of the sky, the taget weight is 6 pounds that what mine came in at. There is a huge discussion on RCU in the 3D section.
Mike. |
|
| Back to top |
|
 |
3dbatixkid Moderator

Joined: 15 Apr 2004 Posts: 1178 Location: Sunnyvale, CA
|
|
| Back to top |
|
 |
torking16
Joined: 09 Feb 2006 Posts: 9
|
Posted: Fri Feb 10, 2006 12:38 pm Post subject: |
|
|
| I don't know what is happening but mine has never stalled even at walking speed for landing. I had my motor quit once but i made a wide turn and brought it in, but I landed in the tall grass because of a cross wind. I am way nose heavy and the cg in the manual is wrong. like i said in the other thread the nose just drops |
|
| Back to top |
|
 |
torking16
Joined: 09 Feb 2006 Posts: 9
|
Posted: Fri Feb 10, 2006 12:40 pm Post subject: |
|
|
the plane to look out for is the d*&^ f90. that SOB snapped on a down line pullout at 1/4 throttle right above the trees IDK  |
|
| Back to top |
|
 |
gmilo

Joined: 28 Nov 2004 Posts: 9 Location: Alamo, CA USA
|
Posted: Sat Feb 11, 2006 1:20 pm Post subject: |
|
|
Had mine setup with an AXI4130-16 motor, Opto77ESC, and two 4200 TP 3s2p packs in series and APC17x10e prop. Hovered a little below half stick. Loved the plane. It flew awesome for fast precision aerobatics and slow speed characterstics exhibited nice stable harrier with a little wing rock I programed out with a little spoilerons switch activated. The elevator pushrod setup IS NOT recommended. Mine failed in flight resulting in a mach1 collision with terra firma.... a total loss. I'm building another one now with dual elevator servos in the tail. Hope this helps
Gmilo |
|
| Back to top |
|
 |
torking16
Joined: 09 Feb 2006 Posts: 9
|
Posted: Sat Feb 11, 2006 3:09 pm Post subject: |
|
|
| D#$* sorry to hear that where the packs smushed up pretty bad. I had to move my servos to get the throw i wanted it was binding really badly. are you gonna stick with the pull-pull rudder? I am also going to switch to hinge points I HATE CA hinges on stuff with big throw they are cracking on both my F90 and extra on the tail. good luck |
|
| Back to top |
|
 |
| |