ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

HELP REPAIRING 33% EDGE
21 posts
 
   3DBatix Forum Index -> Workshop
 
Author Message
Fredy



Joined: 25 Jul 2004
Posts: 45

PostPosted: Tue Jul 27, 2004 7:36 am    Post subject: HELP REPAIRING 33% EDGE  

Hey guys, A flameout killed my edge.

www.compean.com.mx/crash.mov

I need help reparing.

Please help

_________________
I would pay a monthly fee for a 24hr daily "R/C Channel" that can show in Mexico.
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1316
Location: Fremont, CA

PostPosted: Tue Jul 27, 2004 8:04 am    Post subject:  

Sorry to hear about your Edge Amigo, it looks like it starved fuel. Was the clunk line still intact? Do you run a fuel filter? Check the carb screen on your DA, maybe it's clogged. It sounded like it did a couple of hiccups just before it died. I don't think that's worth repairing, you'll spend more money and time repairing it. I've seen that happen to Zak a few times. Shocked
_________________
--Meyrick--
Back to top  
3dav8r



Joined: 25 Apr 2004
Posts: 28
Location: Salinas,Ca

PostPosted: Tue Jul 27, 2004 8:08 am    Post subject: Dude...You balled it up bad!!  

There may be hope if you didnt do to much danage to the inside of the wings with the wing tube taking out the internal support.
Take a hard look at those wings and good luck.
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1178
Location: Sunnyvale, CA

PostPosted: Tue Jul 27, 2004 8:31 am    Post subject:  

It wasnt the ignition. The engine sagged before it quit, and if the ignition, or ignition battery was the problem, then there would have been no hesitation and it would have just quit. By the sounds of the engine in the air, i would check the screen in the carb like meyrick said. Mine was bogging a bit and i found that the screen was dirty, and it ran a lot better after that.

Sorry about the loss, ive been there myself.

_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
Fredy



Joined: 25 Jul 2004
Posts: 45

PostPosted: Tue Jul 27, 2004 2:42 pm    Post subject:  

I'll chech that! I've never taken it appart so I might come back for help with that.
_________________
I would pay a monthly fee for a 24hr daily "R/C Channel" that can show in Mexico.
Back to top  
Fredy



Joined: 25 Jul 2004
Posts: 45

PostPosted: Tue Jul 27, 2004 2:52 pm    Post subject:  

Yep, I'm back

which Should I unscrew??



IMG_0044.jpg
 Description:
 Filesize:  35.87 KB
 Viewed:  360 Time(s)

IMG_0044.jpg



_________________
I would pay a monthly fee for a 24hr daily "R/C Channel" that can show in Mexico.


Last edited by Fredy on Tue Jul 27, 2004 2:59 pm; edited 1 time in total
Back to top  
Fredy



Joined: 25 Jul 2004
Posts: 45

PostPosted: Tue Jul 27, 2004 2:57 pm    Post subject:  

Meyrick wrote:
Sorry to hear about your Edge Amigo, it looks like it starved fuel. Was the clunk line still intact? Do you run a fuel filter? Check the carb screen on your DA, maybe it's clogged. It sounded like it did a couple of hiccups just before it died. I don't think that's worth repairing, you'll spend more money and time repairing it. I've seen that happen to Zak a few times. Shocked


1. Yes I run fuel filters on the Jersey modelers fuel can. It came with two, One as a clunck and another in the tubing. shouldn't that be enough?

2. I also hear in the video a couple of hiccups, but thought it was an editing mistake or something like it. I sure didn't notice them while flying......... frown

3. You really think is unrepairable??

_________________
I would pay a monthly fee for a 24hr daily "R/C Channel" that can show in Mexico.
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1316
Location: Fremont, CA

PostPosted: Tue Jul 27, 2004 3:51 pm    Post subject:  

Fredy wrote:
Yep, I'm back

which Should I unscrew??


The screen is on the back plate of the carb where it's stamped walbro. Remove those 4 screws.

_________________
--Meyrick--
Back to top  
Fredy



Joined: 25 Jul 2004
Posts: 45

PostPosted: Tue Jul 27, 2004 3:53 pm    Post subject:  

I'm taking it appart now, but really have no ide what I'm doing.

I've unscrewed this side of the carb, and there was some gue in there, but it doesn't seem enough to say it was cloughed.

here's a picture.



IMG_0001.jpg
 Description:
 Filesize:  23.4 KB
 Viewed:  353 Time(s)

IMG_0001.jpg



_________________
I would pay a monthly fee for a 24hr daily "R/C Channel" that can show in Mexico.
Back to top  
Fredy



Joined: 25 Jul 2004
Posts: 45

PostPosted: Tue Jul 27, 2004 3:55 pm    Post subject:  

Should I also unscrew the other side???

Or is there anything I should be AWARE of not taking appart???



IMG_0002.jpg
 Description:
 Filesize:  23.84 KB
 Viewed:  352 Time(s)

IMG_0002.jpg



_________________
I would pay a monthly fee for a 24hr daily "R/C Channel" that can show in Mexico.
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1316
Location: Fremont, CA

PostPosted: Tue Jul 27, 2004 3:57 pm    Post subject:  

Fredy wrote:

1. Yes I run fuel filters on the Jersey modelers fuel can. It came with two, One as a clunck and another in the tubing. shouldn't that be enough?

2. I also hear in the video a couple of hiccups, but thought it was an editing mistake or something like it. I sure didn't notice them while flying......... frown

3. You really think is unrepairable??


1. Yes you definitely need a filter between the fuel tank and the carb. Filtering it from the fuel can is not enough.

2. Sometimes you won't notice a hiccup when your concentrating so much on torkin. big grin

3. Anything is repairable, for me it's a lot of work and I figure the plane cost $999 ARF and would probably spend almost half of the cost of a brand new one. Plus the time you would spend to repair and you would always ask yourself if it would fly the same as before. To me, it's just not worth my time.

_________________
--Meyrick--
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1316
Location: Fremont, CA

PostPosted: Tue Jul 27, 2004 4:06 pm    Post subject:  

Fredy wrote:
Should I also unscrew the other side???

Or is there anything I should be AWARE of not taking appart???


That's the right plate you removed, the screen should be as big as a servo output shaft. Very small.

_________________
--Meyrick--
Back to top  
Fredy



Joined: 25 Jul 2004
Posts: 45

PostPosted: Tue Jul 27, 2004 4:23 pm    Post subject:  

Thanks,

Can you see the gue I reffer to. In the picture above? I just want to make sure what caused the flame out. Do you think that gue is enought to starve the motor?
I still haven't ruled out the possibility of the ignition battery being disoldered in flight........

check it out..



battdisold.jpg
 Description:
 Filesize:  30.71 KB
 Viewed:  346 Time(s)

battdisold.jpg



_________________
I would pay a monthly fee for a 24hr daily "R/C Channel" that can show in Mexico.
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1316
Location: Fremont, CA

PostPosted: Tue Jul 27, 2004 5:26 pm    Post subject:  

Fredy wrote:
Thanks,

Can you see the gue I reffer to. In the picture above? I just want to make sure what caused the flame out. Do you think that gue is enought to starve the motor?
I still haven't ruled out the possibility of the ignition battery being disoldered in flight........

check it out..


Was that how it came out? Is that still somehow connected still after the crash?

_________________
--Meyrick--
Back to top  
Fredy



Joined: 25 Jul 2004
Posts: 45

PostPosted: Tue Jul 27, 2004 5:35 pm    Post subject:  

This is how it came out. And no, it wasn't conected when I saw it. The doubt that I have is because I had already pulled the plane out of the bushes it landed it and I'm not sure if it's possible that it got jammed out then. If I had seen it disconected before moving the plane then I'd be 99% sure that IT caused the problem. I'm not sure if the crash was strong enough to jam the cable out of the deans connector.


battdisold2.jpg
 Description:
 Filesize:  29.02 KB
 Viewed:  342 Time(s)

battdisold2.jpg



_________________
I would pay a monthly fee for a 24hr daily "R/C Channel" that can show in Mexico.
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1178
Location: Sunnyvale, CA

PostPosted: Tue Jul 27, 2004 9:33 pm    Post subject:  

I can guarantee it wasnt your ignition. The hiccups you hear in the video tell that it was running out of fuel. you have the right screen there. And yes, the goo will cover it. Some of the gas cans have a treatment to the plastic inside them, which is dissolved somewhat by the gasoline. That stuff that dissolves is now in your gas, and gets caught on the edges of the screen. it can build up over time and create a film over the screen.

Also, i could hear in the video that it wasnt running perfectly smoothe. When mine started to do this, i checked that screen, and it was dirty.

If you want to take the other plate off, be warned that there is a spring in there with a little lever arm that is connected to the diaphram, so you cannot just lift the plate off the carb. it has to come up, and then slide to dis-engage the spring and lever. Just make sure that there are no bits of debris in there. It would also be wise to blow carb cleaner through the ports in the carb.

_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
Fredy



Joined: 25 Jul 2004
Posts: 45

PostPosted: Wed Jul 28, 2004 4:57 am    Post subject:  

Well thanks alot Zak, I've seen all your videos and reading much of your posts. I'm convinced of you experience and I have suggestions strongly in mind. Thanks a bunch!

Now I'm alittle confused since all these things are new to me.

Quote:
you have the right screen there.....


You mean the fuel screen?

Quote:
And yes, the goo will cover it


You mean that it is enough to starve the plane? I take it that's a YES because it's not only whats visible but also the thin film layer you meniton?

Quote:
If you want to take the other plate off.......,


Should I? Is there another screen there?

Quote:
It would also be wise to blow carb cleaner through the ports in the carb.


Carb cleaner??? Ports in the carb????

Thanks in advance Zak

P.S. And I guess that now that it is all opened it wouldn't hurt to brush some after run oil in there eh?

_________________
I would pay a monthly fee for a 24hr daily "R/C Channel" that can show in Mexico.
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1178
Location: Sunnyvale, CA

PostPosted: Wed Jul 28, 2004 1:20 pm    Post subject:  

outlined in red are the ports that should be cleaned. The blue circle shows the filter screen, which you should take out (use a pin to carefully pull it out) and also clean behind that with carb cleaner. The green area im not sure is a port, but should be cleaned as well.

hope this helps

after run isnt needed, just make sure the thing is clean.

you dont need to take the other plate off if you dont want, there is NOT another screen in there.



fredys carb highlighted pic.jpg
 Description:
 Filesize:  84.93 KB
 Viewed:  194 Time(s)

fredys carb highlighted pic.jpg



_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
Fredy



Joined: 25 Jul 2004
Posts: 45

PostPosted: Wed Jul 28, 2004 3:11 pm    Post subject:  

You guys are awesome!!!

big grin big grin big grin

_________________
I would pay a monthly fee for a 24hr daily "R/C Channel" that can show in Mexico.
Back to top  
Fredy



Joined: 25 Jul 2004
Posts: 45

PostPosted: Wed Jul 28, 2004 5:03 pm    Post subject:  

How's this for a carb cleaner?

http://products3.3m.com/catalog/us/en001/auto_marine_aero/aerospace/node_GSTXY39Y7Mbe/root_GST1T4S9TCgv/vroot_GSNNJ6NQDKge/gvel_GSVYPFP6VHgl/theme_us_aerospace_3_0/command_AbcPageHandler/output_html

Ever used that?

_________________
I would pay a monthly fee for a 24hr daily "R/C Channel" that can show in Mexico.
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1178
Location: Sunnyvale, CA

PostPosted: Wed Jul 28, 2004 9:47 pm    Post subject:  

That stuff looks fine, any carb cleaner should work. I used the Gumout brand, but 3M is just fine.
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
 
   3DBatix Forum Index -> Workshop All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive